Page History

...

1. Open the Hardware tab in the System Settings window (1).
2. In the object tree on the left side of the Hardware tab, select the Traffic Detector object representing the Traffic Detector module to be set up. The settings panel of the selected object will open on the right side of the window (2).
   
3. Click the Markings setup button and select the Set markings item (3).
4. The Advanced settings window opens.
5. In the Advanced settings window, select the video frame to be used for markings setup.
   To select the frame, click the Select frame button at the appropriate moment.
   
   The Advanced settings window closes and the Keypoints Camera Calibration window opens.In the Keypoints window,
6. Set the switch into the Specify camera parameters position to set camera parameters or into the Specify reference points position to set the keypoints, signifying the markings..
   To set camera parameters, do the following:
   1. In the Camera height (m) field enter the height of the camera mounting in meters (1).
   2. In the Focus (mm) field enter the focal distance in millimeters (2).
   3. In the Effective pixels section enter the number of effective pixels in horizontal and vertical direction (3).

   4.  In the Pixel size (um) enter the size of pixel in horizontal and vertical direction (4).
      Image Added
      In case of switch is set into the Specify reference points position:

      Info
      title Note.
      A keypoint is a small object or a marking easily identified in the image. The actual road markings can be used as key points. No more than two points should lie on a single straight line. The keypoints should be as far from each other as possible, although inside the camera viewing zone. The farther the keypoints are from each other, the more precise will be the setup. Measure and write down the coordinates of actual keypoints on the road relative to any origin. These will be the ground coordinates of the keypoints.

   Image Removed

   At this stage you must

   1. Image Added
      It is required to specify four keypoints and their coordinates.

   By

   1. On default, keypoints are

   set

   1. specified automatically.

      To change

   the

   1. keypoints and their coordinates do the following:

   6.1
   1. 1. Remove from the screen the keypoint whose coordinates you want to change. This requires a point with the mouse and hold down the
   «Shift»
   1. 1. Shift, press the left mouse button.
   6.2
   1. 1. Click the position for a keypoint in the video frame and press the left mouse button.
   6.3
   1. 1. In the zoom window that opens, mark the keypoint and enter the ground oordinates in the X and Y fields.
         
   Image Removed
   1. 1. Image Added
   6.4

   1. 1. Click OK.

7. To go to the following step of setting press the Next button.

8. The

   Road marking

   Working zone window opens. This window allows setting the road edges, number of lanes and the driving directions.
   Image Modified

   
   

   By default the road marking is set automatically.
   To set the markings, do the following:

   8.1
   1. To remove the road edge Shift click one of its endpoints by pressing the left mouse button (
   a
   1. 1).
   8.2
   1. To set the road edge, click the road edge in the image, press the left mouse button, drag the cursor to another edge of the road in the video frame, release the button (
   a
   1. 2).
   8.3
   1. Set the number of driving lanes (
   b
   1. 3).
   8.4
   1. Set the driving direction for each lane (
   c
   1. 4).
      To go to the following step of setting press the Next button.
9. The Marking result window opens.
   Image Modified
   The image with the road markings is displayed as the result of the setup.
   To change the width of lane mouse over the internal border of the road markings and expand it to the required size clicking the left mouse button.
10. Set the Projection checkbox to view the projective image.
    Image Modified
    Click the Finish button to complete the setup.
11. Click Apply (4).

...