Page History

Adding fingerprints of users from the Access Manager using the Suprema BioMini biometric control reader is carried out as follows:

1. Display the Open the Access Manager window  window (see see Starting and stopping the Access Manager module).Go  Go to user editing (see see Going to user editing).
2. Right-click the user's photo and select Extensions select Extensions -> > (SupremaEdit Fingerprints) Suprema BioMini.
3. To add a new fingerprint, click the Add button in the Suprema. Edit fingerprints window.
   Image RemovedImage Added
   The Suprema dialog box opens. Capture fingerprints window will open.
   Image Modified
4. Already added user fingerprints are displayed in the (1) list. First two fingerprints highlighted in bold will be recorded to the Suprema controller. To delete a fingerprint, select it in the list and click Remove (2). To delete all user fingerprints, click Remove all (3).
5. To add a new fingerprint, click Add (4).
6. Configure parameters of fingerprint capturing in the dialog box opened:
   Image Removed
   
   1. Select minimum quality of a fingerprint to be accepted by the system in the Quality dropdown list (1). Fingerprint will be scanned by the system until its quality is not less than the specified value.
   2. Select minimum similarity level of fingerprints in the Security Level dropdown list (2). The second fingerprint will be scanned by the system until its similarity to the first one is not less than the specified value.
7. Click Start Capturing (3).
8. Put user finger to the control reader.

9. Wait until two copies of a fingerprint are scanned. The fingerprint image is displayed in the corresponding area as soon as it is scanned (1).

   Image Removed

   Info
   title Note.
   Scanning can be interrupted in any moment by the Abort Capturing button.

10. To finish fingerprint scanning, click OK (2).

11. From the Mode drop-down list (1) select the fingerprint One finger capture mode.
12. From the Quality drop-down list (2) select the fingerprint capture quality:
    
    • 20 (Weak) - low quality.
    • 40 (Moderate) - average quality (default).
    • 60 (Strong) - high quality.
    • 80 (Strongest) - the highest quality.

13. To start capturing fingerprints, click the Start capturing button (3) and follow the instructions displayed at the top of the Suprema. Capture fingerprints window.

    Info
    title Note
    To capture fingerprints, each finger or group of fingers should be placed on the reader twice with 5 seconds delay after pressing the Start capturing button and after the first capture.

    
    

14. After the fingerprint capture is completed, select the type of scanned finger for each fingerprint in the drop-down list (1):

    • Undefined - неопределенный.
    • Left thumb - thumb of the left hand.
    • Left index finger - index finger of the left hand.
    • Left middle finger - middle finger of the left hand.
    • Left ring finger - ring finger of the left hand.
    • Left little finger - little finger of the left hand.
    • Right thumb - thumb of the right hand.
    • Right index finger - inder finger of the right hand.
    • Right middle finger - middle finger of the right hand.
    • Right ring finger - ring finger of the right hand.
    • Right little finger - little finger of the right hand.

    Image Added

15. Unset the Add check box (2) if it is not necessary to add the fingerprint to the user.

16. Click OK (3) to save the result.

17. The captured fingerprints will be displayed in the Suprema. Edit fingerprints window.
    Image Added

18. To remove one fingerprint, select it and click Remove.

    Info
    title Note
    To remove all fingerprints, click Remove all.

    
    

19. To mark a fingerprint as captured "Under duress", select it and click the [Duress] button.

    Info
    title Note
    As a result, an alarm will be generated when reading this fingerprint.

    
    

20. To move a fingerprint up or down in the list, select it and click the Up or Down button.

21. Click Ok and then save the user settingsRepeat steps 6-11 for all required user fingerprints. Click OK (5).