Go to documentation repository
Page History
Before you install Axxon Next:
- Убедитесь что все Серверы подключены к uninterruptible Make sure all Servers are connected to an uninterruptible power supply (UPS).
- Для предотвращения частых обновлений системы, которые могут привести к неработоспособности, рекомендуется использоваться To prevent frequent system updates, which can cause system inoperability, it is recommended to use Windows 10 LTSB или or Windows Server (see Operating system requirements).
- Install all the latest Windows service/update packs.
- Synchronize the system time with world time and specify the correct time zone.
- For each Server, specify a unique Windows hostname.
- Specify a new password for the account of local administrator.
- Synchronize the time of all Servers and IP devices.
- Create another administrator account for backup. Specify a password for it.
...
Antivirus configuration (see Appendix 4. Using Axxon Next with anti-virus software):
-
Добавить в исключения следующие процессыAdd the following processes to the exclusion list:
- consul.exe;
- nomad.exe;
- apphost.exe;
- postgres.exe.
- Добавить в исключения следующие папкиAdd the following folders to the exclusion list:
- C:\ProgramData\AxxonSoft\AxxonNext;
- C:\Program Files\AxxonSoft\AxxonNext;
- C:\Program Files\Common Files\AxxonSoft;
- Postgres and metadata folders if they are not default.
- Добавить в исключения следующие портыAdd the following ports to the exclusion list:
- 20109-20210;
- 4000 (only for Failover installation type);
- 4646-4648 (only for Failover installation type);
- 8300-8302 (only for Failover installation type);
- 8500 (only for Failover installation type);
- 8600 (only for Failover installation type).
...
- Connect the cameras to the Servers.
- Синхронизируйте время всех Серверов и камер с одним NTP серверомSynchronize the time of all Servers and cameras with a single NTP server.
- Add the cameras to the system (see Adding and removing IP devices, Bulk creation of IP devices). Preferred protocol: ONVIF generic.
-
Multistreaming:
Make sure that for each camera different stream IDs are selected as High quality and Low quality streams.
- Low quality stream settings should be lower than the High quality stream.
- Codec type*: рекомендуется использовать H.265 или or H.264 . Если планируется использовать Web Клиент, то рекомендуется H.264 - использование H.265 приводит к рекомпрессии потока на стороне СервераFPS: для корректной работы детекторов частота кадров Low quality stream должна быть не менее 6is recommended. If you plan to use the Web Client, then H.264 is recommended since using H.265 leads to the stream recompression on the Server side.
- FPS: the Low quality stream frame rate should be at least 6 to ensure the correct operation of the detection tools.
- Resolution:
- Aspect ratio should be the same for Low and High quality streams*.
- Для корректной работы детекторов разрешение Low quality stream должно быть не менее 640x360 и не более 1280x720The Low quality stream resolution should be no less than 640x360 and no more than 1280x720 to ensure the correct operation of the detection tools.
- Bitrate:
Recommended type*: VBR + limit.
Set maximum bitrate / bandwidth limitation.
Recommended bitrate: 1 mbps per 1 MP.
- GOV (also known as GOP, I Frame, etc.): it is recommended to have at least one keyframe per second.
*May differ for different camera models.
...
Archive recording configuration (see Binding a camera to an archive):
- Link each camera to at least one archive.
- Configure recording to the archive (permanent or triggered by detection tools) for each camera.
-
Make sure pre-recording is enabled (> 1 sec).
-
Note that after you re-create the archive, it is necessary to re-create all recording rules in the detection tool settings or Programming settings.
...
- The motion detection tool should operate on a low quality stream (see Configuring VMD).
- Настроить маски для областей кадра, которые постоянно триггерят движения (например, индикатор времени или телевизорConfigure masking of the frame areas which constantly trigger motion detection (for example, on-screen display (OSD) or TV).
- Create automatic rules for recording to the archive (see Automatic Rules).
- Use a NVIDIA GPU for the detection tools operation if there is one.
...
- Do not use H.265 in camera settings — since it will cause causes the stream recompression on the Server side. It is recommended to use H.264 for such cameras.
- Change the HTTP port from 80 to a custom port (see Configuring the web server).
...
Overview
Content Tools