Page History

The In Axxon PSIM Software System supports the use of , you can use different streams from a video the camera for display displaying video on the Video Surveillance Monitorvideo surveillance monitor, archiving, and video analytics. For example, this feature option lets you display a low-quality video signal on the monitor while writing recording a high-quality signal video to the archive, reducing which reduces the load on the Clientclient.

...

...

...

To configure multistream settings, do the following:

1. Go to the Hardware tab (1) in the System Settings dialog settings window.
2. In the object tree on the Hardware tab, select the previously created Camera object (2) object that corresponds to the video camera for which multistream mode is to be configured. The right part of the Hardware tab shows you want to configure multistreaming mode.
3. Go to the Streams settings tab on the settings panel for the selected object.On the Camera object's settings panel, go to the Streams settings tab (3)of the Camera object.
   Image Modified
4. To enable multistream mode, check the Streams configuring box (4).
5. Set the Streams configuring checkbox to enable multistreaming mode.
6. Set the checkboxes Check the boxes next to the used video streams to enable them (5of the camera (1).

7. Check Set the box checkbox in the the Default column (6) in the line of next to the stream number that should be used you need to use in the following cases:

   1. To display video both locally and on remote clients;.

   2. To send to remote clients, including the Videogate, that can record this video stream;.

      Info
      title Note.
      If a specific video stream is requested via Video gateVideogate, then the requested stream is send to Video gate, not the Default stream one, is transmitted.

   3. When a video

      stream is not specified for the video request

      request doesn't contain a specified video stream.

      Info
      title Note

   .
   This stream is used

   1. You can use this stream, for example, to display video on the

   Video Surveillance Monitor

   1. video surveillance monitor if a default stream has been selected for the camera or for displaying video on the

   Video Surveillance Monitor

   1. video surveillance monitor of the web server.

8. Check Set the box checkbox in the the Video analytics column (7) in the line of the stream number that should be used for the LPR channel column next to the stream number that you need to use for the face recognition server, the main motion detection tooldetector, zone detection toolsdetectors, tracking detection tool detectors, and face detection tool detectors (if an external recognizer is not isn't used).

9. Check Set the box checkbox in the Archive column (8) in the line of the number of stream that is to be recorded column next to the stream number that you need to record to the archive, not upon alarm – the , for example, during continuous recording is performed. Check

10. Set the box checkbox in the the Archive (alarms) column (9) in the line of the number of stream that is to be recorded column next to the stream number that you need to record to the archive upon alarm.

    This stream is also used for Backup archiveYou can use this stream for backup archiving.

    Info
    title Note.
    If you select different streams are selected for recording to the archive upon alarms and continuous recording , when recording is performed non-stop and detection tools nonstop and detectors are enabled, then upon alarm the recording of the current archive fragment is stopped stops upon alarm in the continuous recording stream, and recording of a new fragment starts in the alarm recording stream. When the alarm ends and after prepost-alarm recording, the continuous recording with the corresponding stream resumes. If you select the same stream is selected for recording to the archive upon alarms and continuous recording, then recording of the current fragment is not stopped doesn't stop upon alarm.

    Info
    title Note.
    If you configure pre-alarm recording is configured, then when selecting different streams are selected for recording to the archive upon alarms and continuous recording, some archive recordings overlay as the following video fragment starts before earlier than the previous one ends.

11. Configure the video streams as follows:
    
    1. Go to the tab that corresponds to the desired required video stream (10).
       Image Modified
    2. The Purpose field (11) displays a description of how the video stream is used. field displays the information on how to use a video stream.

    3. In the Codec group, specify the video stream parameters (see The settings Specify the video stream's parameters (12) (see The Settings panel of the Camera object): codec, key frame rate, and video quality.

       Note
       title Attention!
       Following The following video streams are available for Axis cameras: 1. Receiving of H264/MJPEG/MPEG4 video. It is available to specify settings of You can specify video stream settings using the Axxon PSIM software package facilities. Settings are specified . Specify these settings in the Video stream 1 tab. 2-4. Stream corresponding to “Quality”, “Balanced” and “”Bandwidth” profiles. These profiles configure Streams that correspond to the "Quality", "Balanced" and "Bandwidth" profiles. You can configure these profiles in the camera web - interface. Video stream 2 corresponds to the “Quality” "Quality" video stream, Video stream 3 corresponds to the “Balanced” "Balanced" video stream, and Video stream 4 corresponds to the “Bandwidth” "Bandwidth" video stream.

    4. Repeat steps a-d for the remaining video streams.
12. Click the Apply button.

This completes Configuring the process of configuring multistream modemultistream video is complete.