Page History

1

Identification number*

Automatically

Displays the identification number of the Operator protocol object in the system

Sequence of numbers

-

Depends on the number of the Operator protocol objects in the system

2

Name*

Enter the value into the field

Sets the name of the Operator protocol object in the system

Latin, Cyrillic and service characters

Operator protocol

A line containing a sequence of any characters (letters, digits, service characters except > and < characters), case-insensitive.

Number of characters—from 1 to 60

3

Disable

Set the checkbox

Sets the status (enabled or disabled) of the Operator protocol object in the system

Boolean type

Clear

Set—the Operator protocol object is disabled and isn't used

Clear—the Operator protocol object is enabled and used

4

Display

Select the value from the list

Sets the Display parent object for the given Operator protocol object

Name of the Display objects registered in the system.

Name of the Display parent object

Depends on the number of the Display objects in the system

5

X

Enter the value into the field

Sets the X coordinate in the horizontal axis for the upper left corner of the Operator protocol interface window

% of the screen width

-

From 0 to M*100, where M is the number of the installed monitors

Y

Enter the value into the field

Sets the Y coordinate in the vertical axis for the upper left corner of the Operator protocol interface window

% of the screen height

-

From 0 to M*100, where M is the number of the installed monitors

6

W

Enter the value into the field

Sets the width of the Operator protocol interface window

% of the screen width

-

From 0 to M*100, where M is the number of the installed monitors

H

Enter the value into the field

Sets the height of the Operator protocol interface window

% of the screen height

-

From 0 to M*100, where M is the number of the installed monitors

7

Allow moving

Set the checkbox

Allows moving the Operator protocol interface window manually

Boolean type

Clear

Set—allow moving the Operator protocol interface window manually

Clear—disable moving the Operator protocol interface window manually

Opens a test window to set the position of the Operator protocol interface window

11

Type

Select the value from the list

Sets the type of objects, the events from which should be displayed in the Operator protocol window

Available object types

-

Depends on the objects registered in the system.

Only the objects for which the INFORMATION or ALARM value is selected in the Messages processing column on the Events tab in the ddi.exe utility are available for selection (see The Events tab)

12

Number

Select the value from the list

Sets the number of an object, which events should be displayed in the Operator protocol window

Sequence of numbers

-

Depends on the number of the objects of the specified type registered in the system

13

Name

Automatically

Sets the name of an object, which events should be displayed in the Operator protocol window

Names of the objects registered in the system

-

Depends on the objects registered in the system

14

Event type

Select

the value from the list

Sets the events displayed in the Operator protocol interface

window

Events available for the selected object

-

Depends on the object type

15

Request password

Select

the value from the list

Defines the necessity of password to process the event

Boolean type

-

Set—password confirmation is required to process the event

Clear—password confirmation isn't required to process the event

16

Region

Select

the value from the list

Sets the Region object corresponding to the monitored object

List of

the Region objects created in the system

-

Depends on the number of

the Region objects created in the system

17

Parameter

Enter the value

into the field

Sets the parameter of the monitored object

Depends on the event type

-

Depends on the event type

1–10

The

lower the value, the higher the priority

Sets the name of the parameter, the value of which

should be displayed in the Operator protocol interface

window

22

Description

Enter the value

into the field

Enter a short description of the specified parameter

Latin, Cyrillic and service characters

-

0–255 characters

Sets the Operator protocol object, to which the events

should be sent after the time specified in the Wait for operator response for field

Depends on the number of the Map objects created in the system

ActiveX

—archive

will open in a separate window

Monitor

—archive

will open on the selected Video

surveillance monitor

Sets the time after which the event

will be assigned the  Non-processed event type or the event

will be escalated

0–10000

Fractional values can be specified; integer and fractional parts are point-separated. For

example, to set 2 minutes 30 seconds time period

, enter 2.5

Enter the maximum number of events that can be displayed

simultaneously in the list of the current events

0–600

The value is not specified or

0—the operator can not delay the event processing

Greater than

0—the parameter sets the time for which the operator can delay the event processing

Fractional values can be specified; integer and fractional

parts are point-separated. For example, to set

2 minutes

30 seconds time period, enter 2.5

Enables sorting by priority. The descending sorting is performed in this order: Escalated, Alarm, Information and Standard (three latest event parameters can be set in the DDI file - see The Events tab). 

Yes – sorting by priority is enabled.

No – sorting by time events are received is enabled.

Places new events at the end of the current events list

Yes – a new event is placed to the end of the list

No – a new event is added to the beginning of the list

Yes – when the event is processed in one of the Operator protocol, it is deleted from other Operator protocols

No – when the event is processed in one of the Operator protocol, it stays unprocessed in other Operator protocols

Defines the necessity to enter the password to process the event 

Yes – event processing is to be confirmed with a password;

No – password is not required for event processing.

34

The Autoswitch checkbox

Checkbox is set

Enables auto switch to the Current events tab in the Operator protocol window when a new event occurs.

Boolean type

No

Yes – auto switch is enabled

No – auto switch is disabled

Yes – the last received event tile is automatically activated;

No – when the new event is received, the tile selected by the Operator remains active.

Yes – event handling buttons are displayed when a group of events is selected

No – event handling buttons are hidden when a group of events is selected

Yes – the comment field is automatically cleared after the event is processed by the Operator;

No – the comment text remains in the comment field after the event is processed by the Operator.

Yes - the alarm tile size is set equal to the size of the Operator Protocol window area which is not occupied by the event control panel;

No - the tile size is set according to the content size.

Yes - the Apply to all button is hidden in the Operator Protocol window, and the Operator is not able to process all alarms at once;

No - the Apply to all button is available in the Operator Protocol window.

Yes – the Operator protocol window is always displayed above all other windows.

No – the Operator protocol window is displayed normally.

Yes – the buttons for classifying events (Alarm situation, Suspicious situation, False alarm) do not appear until the Comment field is filled.

No – the operator can classify (process) the event without entering a comment.

Prohibits the Operator from selecting multiple events using the Shift and Ctrl keys

Yes – the ability to select multiple events using the Shift and Ctrl keys is disabled.

No – the ability to select multiple events using the Shift and Ctrl keys is enabled.