Versions Compared

Old Version 228

changes.mady.by.user Gleb Matskevich

Saved on

compared with

New Version 229

changes.mady.by.user Yulia Morozova

Saved on

Key

  • This line was added.
  • This line was removed.
  • Formatting was changed.

...

Video analytics

Registry section

String parameter

Available values

Default

Product version

Parameter in effect

x32: (X32)\Video\VMDA

x64: (x64)\Video\VMDA

VMDA.inactiveInterval

>0

-

4.9.0 and later

Key specifies time period in minutes, during which absence of detected objects by tracker is permitted. If the key is created, after the specified time and if there is no activity of VMDA detection, the message about inactivity will be generated. On default, this message is not generated

x32: (x32)\Video\VMDA
x64: (x64)\Video\VMDA		VMDAEXT0, 104.9.8 and later

The key is used for separating the VMDA trackers process to the individual process. It's recommended to do to increase stability and reliability of the Intellect basic features. Allocating trackers to a separate process increases the CPU and memory resources used.

0—process of VMDA trackers is starting in the video.run process

1—process of  VMDA trackers is starting in the individual detector_ext.run process

Note 1. The detector_ext.run process is run under the video.run process. The video.run process controls the detector_ext.run process and restarts it if necessary.

Note 2. It's required to install the Intellect Detector Pack ( version>=2.1.0) for the correct key operation



Note
titleAttention!

If you created many VMDA trackers (for example, about 100), it is highly recommended to set VMDAEXT=1.



x32: (x32)\Video\VMDA
x64: (x64)\Video\VMDA		VMDAEXT.RAM>020004.9.8 and laterThe key is used with the VMDAEXT key and sets the memory space in megabytes which can use the detectror_ext.run process. The process will be restarted if the allocated memory is exceeded. The recommended value is in the range 2000-5000, depending on the hardware resources of the computer

x32:(X32)\Video\VMDA

x64: (x64)\Video\VMDA

VMDA.useSpeedLimitTypeLessThanVMDA detector IDs separated by comma or semicolon-4.10.4 and later

The VMDA detection tool IDs separated by comma or semicolon that should be triggered when the object speed is less than the speed configured for the VMDA detection tool.

Note 1. If no ID is specified for this parameter, or there is no parameter at all, the detection tool is triggered when an object crosses the line in the selected direction with a speed that is approximately the same as the speed configured for the VMDA detection tool. 

Note 2. The same VMDA detector id can only be specified for either the VMDA.useSpeedLimitTypeLessThan or the VMDA.useSpeedLimitTypeMoreThan (see below) parameters. The simultaneous operation of both these parameters for the same VMDA detector is not allowed

x32:(x32)\Video\VMDA

x64: (x64)\Video\VMDA

VMDA.useSpeedLimitTypeMoreThanVMDA detector IDs separated by comma or semicolon-4.10.4 and later

The VMDA detection tool IDs separated by comma or semicolon that should be triggered when the object speed is greater than the speed configured for the VMDA detection tool.

Note 1. If no ID is specified for this parameter, or there is no parameter at all, the detection tool is triggered when an object crosses the line in the selected direction with a speed that is approximately the same as the speed configured for the VMDA detection tool. 

Note 2. The same VMDA detector id can only be specified for either the VMDA.useSpeedLimitTypeLessThan (see above) or the VMDA.useSpeedLimitTypeMoreThan parameters. The simultaneous operation of both these parameters for the same VMDA detector is not allowed

x32: (x32)\Video\VMDA
x64: (x64)\Video\VMDA		VMDA.ignoreAnaliticStream0, 104.9.8 and later

The key sets the camera stream used by the detection modules included in the Detector Pack subsystem.

0 – the Video Analytics stream is used

1 – the Default stream is used

Note. If the camera is not used in the multi-thread mode, the first stream (the only one) will be used regardless of the key value

x32: (x32)\Video\VMDA
x64: (x64)\Video\VMDA		VMDAEXT.DEBUGGER0, 104.11.0 and later

The key is used in conjunction with VMDAEXT = 1 (see above). Disables the restart of the Detector_Ext.run module by the Video.run module.

0 – the Detector_Ext.run process is restarted as necessary

1 – the Detector_Ext.run process is not restarted

x32: (x32)\Video\
x64: (x64)\Video\		DrawAngleArrow 0, 114.11.2 and later

The key disables an arrow showing the movement direction of an object detected by the Tracker in the Video Surveillance Monitor.

0 – direction arrow is not displayed

1 – direction arrow is displayed

x32: (x32)\Video\VMDA

x64: (x64)\Video\VMDA

VMDA.oneAlarmPerTrack0, 1014.11.0 and later

The key is used together with the key VMDAEXT = 1 (see above). The key determines the alarm generation mode.

0 – one track – many alarms

1 – one track – one alarm

If the key isn't created, the VMDA trackers and neural trackers operate as if VMDA.oneAlarmPerTrack = 1

x32: (X32)\Video\VMDA
x64: (x64)\Video\VMDA		VMDA.SendNewObjectEventToCore0, 114.11.3 and later

The key disables sending events CAM|NEW_OBJECT and CAM|OBJECT_LOST to the core.

0 – events will not be sent to the core

1 – events will be sent to the core

...