Page History

The RTSP-Server object is to be created and configured and You must create and configure the RTSP Server object and add to it all the required cameras are to be added to it before configuring the before you configure the ONVIF-Server module - (see Configuring the RTSP Server module).

The ONVIF-Server object is created under on the basis of the Computer object in on the Hardware tab of the System settings dialog box window.

Configure You can configure the ONVIF-Server object on the Basic settings tab as follows:

1. Go to the settings panel of the ONVIF-Server object.
   Image Modified
2. Specify the port number used to connect to the
Server
3. server (1).
Select the network interface used to connect to the Server in the
4. From the IP-interface drop-down list (2), select the network interface used to connect to the server.
In
5. From the RTSP-server drop-down list (3),select the RTSP
-Server
6. server used
along
7. together withthis ONVIF-Server
(3)
8. object.
9. In the Brand (4) and Model (5) fields, specify the names that
will be
10. are displayed while searching in various clients that support getting the stream over ONVIF
, e.g.
11. , for example, ONVIF Device Manager.
12. By default, the ONVIF 1.X standard is used to transmit video. The ONVIF 1.X
is in use
13. standard corresponds to ONVIF profile S and is used to transmit video in MPEG, MJPEG, and H264 formats (always enabled). If you want to transmit video in H265
or H264 format is to be transmitted, then set the
14. , H264, MPEG, or MJPEG formats according to the ONVIF 2.X standard that corresponds to ONVIF profile T, set the Use Media2 service checkbox
checked
15. (6). In this case, in addition to profile S, profile T is also enabled. For more information about ONVIF profiles, see Main ONVIF profiles.
16. Set the Allow DHCP setting checkbox
checked if
17. (7) if the network uses the DHCP protocol
is in use (7)
18. .

19. By default, the WS-Discovery mode is enabled for the ONVIF -Serverserver. Set Clear the Discovery mode checkbox unchecked (8) in order to disable it (8).

    Info
    title Note
    All the applications using apps that use port 3702 must be shut down on the computer where the ONVIF-Server is started for proper operation of the Discovery mode. Processes You can see processes and ports occupied by them can be seen using the Netstat -ano -p udp command.

20. In From the Department drop-down list (9), select the department where the users will be are created when they are added via the ONVIF-Server interface (9).

    Info
    title Note
    Users are created You can create users in the ONVIF-Server interface using the third-party software, e.g.for example, ONVIF Device Manager. The Administrator rights are required to create users – (see Configuring rights to use ONVIF Serverwork with the ONVIF server).

21. If it is required to redirect all RTSP

-Server

22. server and ONVIF

-Server

23. server requests to the specified port, set the Use RTSP over HTTP Proxy checkbox (10) and specify the port number in the Port field (11). This

may

24. can be necessary for the ONVIF

-Server

25. server operation behind NAT.

26. If it is necessary for the ONVIF
-Server
27. server to use a specific IP address behind NAT in responses to
Clients
28. clients, enter this address in the NAT IP address field (12). This
may
29. can be necessary, for example, if
Clients
30. clients connect not from the local network
,
31. but from the
Internet
32. internet via an external IP address.

33. Click the Apply button.

The ONVIF-Server object is now configured. Now it is possible to configure getting video using  Now you can proceed to setting up video reception via the ONVIF-Server module.

...