Page History

AUTOFOCUS_ON—enable autofocus

tel_prior<>

Priority (1—low, 2—medium, 3—high)

AUTOPAN_END_P—specify the end point of autopan

tel_prior<>

Priority (1—low, 2—medium, 3—high)

AUTOPAN_START—start autopan

tel_prior<>

Priority (1—low, 2—medium, 3—high)

AUTOPAN_START_P—specify the start point of autopan

tel_prior<>

Priority (1—low, 2—medium, 3—high)

AUTOPAN_STOP—stop autopan

tel_prior<>

Priority (1—low, 2—medium, 3—high)

CLEAR_PRESET—clear the selected preset

tel_prior<>

Priority (1—low, 2—medium, 3—high)

preset<>

Preset

D2OFF—disable the additional dynamic settings for Panasonic

PTZ cameras used to increase the quality of analog video signal

tel_prior<>

Priority (1—low, 2—medium, 3—high)

D2ON—enable the additional dynamic settings for Panasonic

PTZ cameras used to increase the quality of analog video signal

tel_prior<>

Priority (1—low, 2—medium, 3—high)

DOWN—

rotate camera lens down

tel_prior<>

Priority (1—low, 2—medium, 3—high)

FOCUS_IN

—focus camera lens on the image

tel_prior<>

Priority (1—low, 2—medium, 3—high)

FOCUS_OUT

—defocus camera lens

tel_prior<>

Priority (1—low, 2—medium, 3—high)

FOCUS_STOP—stop focus/defocus

tel_prior<>

Priority (1—low, 2—medium, 3—high)

ZOOM_IN—zooming in the image

tel_prior<>

Priority (1—low, 2—medium, 3—high)

ZOOM_OUT—zooming out the image

tel_prior<>

Priority (1—low, 2—medium, 3—high)

ZOOM_STOP—stop zooming in/out

the image

tel_prior<>

Priority (1—low, 2—medium, 3—high)

GO_PRESET—

rotate camera to the position specified

in the preset

tel_prior<>

Priority (1—low, 2—medium, 3—high)

preset<>

Preset

HOME—

rotate camera to the initial (home) position

tel_prior<>

Priority (1—low, 2—medium, 3—high)

IRIS_CLOSE—close diaphragm

tel_prior<>

Priority (1—low, 2—medium, 3—high)

IRIS_OPEN—open diaphragm

tel_prior<>

Priority (1—low, 2—medium, 3—high)

IRIS_STOP—stop diaphragm

tel_prior<>

Priority (1—low, 2—medium, 3—high)

LEFT—

rotate camera lens to the left

tel_prior<>

Priority (1—low, 2—medium, 3—high)

LEFT_DOWN—

rotate camera lens to the left and down

tel_prior<>

Priority (1—low, 2—medium, 3—high)

LEFT_UP—

rotate camera lens to the left and up

tel_prior<>

Priority (1—low, 2—medium, 3—high)

PATROL_LEARN—start procedure of patrol programming performed by recording the

camera actions

tel_prior<>

Priority (1—low, 2—medium, 3—high)

point<>

Point number

preset<>

Preset number (tour)

dwell<>

Dwell time in a point in seconds

speed<>

Speed of movement to a point

flush_tour<>

1—flush tour

0—don't flush tour

PATROL_PLAY—start patrolling

tel_prior<>

Priority (1—low, 2—medium, 3—high)

PATROL_STOP—stop patrolling

tel_prior<>

Priority (1—low, 2—medium, 3—high)

RIGHT—

rotate camera lens to the right

tel_prior<>

Priority (1—low, 2—medium, 3—high)

RIGHT_DOWN—

rotate camera lens to the right and down

tel_prior<>

Priority (1—low, 2—medium, 3—high)

RIGHT_UP—

rotate camera lens to the right and up

tel_prior<>

Priority (1—low, 2—medium, 3—high)

SET_PRESET—record the current position

of camera to the selected preset

tel_prior<>

Priority (1—low, 2—medium, 3—high)

preset<>

Preset

STOP—

stop camera lens rotation

tel_prior<>

Priority (1—low, 2—medium, 3—high)

UP—

rotate camera lens up

tel_prior<>

Priority (1—low, 2—medium, 3—high)

SETUP—set up PTZ device

address<>

Device address

cam<>

Camera ID

for control

flags<>

Flag of object operating (0

—enabled, 1

—disabled)

name<>

Object name of PTZ device

speed<>

Speed

SEND_BUFFER—send command to the COM port in the hexadecimal format

buffer<>

Command in the hexadecimal format

parent_id<>

Number of the Telemetry Controller parent object.

Mandatory parameter

tel_prior<>

Priority (1—low, 2—medium, 3—high). The value of the parameter must be greater than 0

LOCK—lock. Switch the telemetry

to the LOCKED state for a specified time

tel_prior<>

Priority (1—low, 2—medium, 3—high). The value of the parameter must be greater than 0. It is forbidden to perform control commands with a lower priority than the specified one during the lock time

duration<>

Lock duration. If the parameter

isn't specified, the lock is valid until the UNLOCK command is executed

UNLOCK—unlock. Switch the telemetry

to the UNLOCKED state

NA

NA