Go to documentation repository
Page History
Adding fingerprints of users from the Access Manager using the Suprema BioMini biometric control reader is carried out as follows:
- Display the Go to adding biometric data in the Access Manager window (see Starting and stopping the Access Manager module Adding biometric parameters).
- Go to user editing (see Going to user editing).
- Right-click the user's photo and select Extensions -> (Suprema) Suprema BioMini.
- The Suprema dialog box opens.
- Already added user fingerprints are displayed in the (1) list. First two fingerprints highlighted in bold will be recorded to the Suprema controller. To delete a fingerprint, select it in the list and click Remove (2). To delete all user fingerprints, click Remove all (3).
- To add a new fingerprint, click Add (4).
- Configure parameters of fingerprint capturing in the dialog box opened:
- Select minimum quality of a fingerprint to be accepted by the system in the Quality dropdown list (1). Fingerprint will be scanned by the system until its quality is not less than the specified value.
- Select minimum similarity level of fingerprints in the Security Level dropdown list (2). The second fingerprint will be scanned by the system until its similarity to the first one is not less than the specified value.
- Click Start Capturing (3).
- Put user finger to the control reader.
Wait until two copies of a fingerprint are scanned. The fingerprint image is displayed in the corresponding area as soon as it is scanned (1).
Info title Note. Scanning can be interrupted in any moment by the Abort Capturing button. To finish fingerprint scanning, click OK (2).
- Select the (Edit Fingerprints) Suprema BioMini extension that corresponds to the Suprema BioMini control reader.
- The Suprema. Edit fingerprints dialog box will open. To add a new fingerprint, click the Add button.
The Suprema. Capture fingerprints window will open. - From the Mode drop-down list (1) select the fingerprint One finger capture mode.
- From the Quality drop-down list (2) select the fingerprint capture quality:
- 20 (Weak) - low quality.
- 40 (Moderate) - average quality (default).
- 60 (Strong) - high quality.
- 80 (Strongest) - the highest quality.
To start capturing fingerprints, click the Start capturing button (3) and follow the instructions displayed at the top of the Suprema. Capture fingerprints window.
Info title Note To capture fingerprints, each finger or group of fingers should be placed on the reader twice with 5 seconds delay after pressing the Start capturing button and after the first capture.
After the fingerprint capture is completed, select the type of scanned finger for each fingerprint in the drop-down list (1):
- Undefined - undefined.
- Left thumb - thumb of the left hand.
- Left index finger - index finger of the left hand.
- Left middle finger - middle finger of the left hand.
- Left ring finger - ring finger of the left hand.
- Left little finger - little finger of the left hand.
- Right thumb - thumb of the right hand.
- Right index finger - index finger of the right hand.
- Right middle finger - middle finger of the right hand.
- Right ring finger - ring finger of the right hand.
- Right little finger - little finger of the right hand.
Uncheck the Add check box (2) if it is not necessary to add the fingerprint to the user.
Click OK (3) to save the result.
The captured fingerprints will be displayed in the Suprema. Edit fingerprints window.
To remove one fingerprint, select it and click Remove.
Info title Note To remove all fingerprints, click Remove all.
To mark a fingerprint as captured "Under duress", select it and click the [Duress] button.
Info title Note As a result, a silent alarm will be generated when reading this fingerprint.
To move a fingerprint up or down in the list, select it and click the Up or Down button.
To finish entering fingerprints, click OKRepeat steps 6-11 for all required user fingerprints. Click OK (5).
Adding fingerprints of users from the Access Manager using the Suprema BioMini biometric control reader is completed.