Page History

General information

You can add video cameras and IP Servers devices to the system by using the IP Device Discovery Wizard.
To open the IP Device Discovery Wizard, click the Add device ... link link at the end of the Server device list.
Image Removed
When the Wizard is opened for the first time after the Client is started, automatic search for new devices will begin. During subsequent sessions, to launch the Wizard you must click the corresponding button. A progress bar indicates search progress.
Image Added

The IP Device Discovery Wizard interface includes:

• Automatic device search.
• Manual entry of device data.
• Adding devices to the configuration.
• Bulk adding devices using .CSV files (see Bulk creation of IP devices).

Automatic search for IP devices

IP devices search

To start searching for devices, click the Search button. While searching, a progress bar is displayed.

To stop devices device search at any time, click the Stop button.

...

...

Since multicast packets are used for device search, the search results may not contain the Servers and devices from other subnets.

The search results are color-coded based on the status of the device.

Filtering IP device search results

Search results can be filtered in two ways:

1. By status. To hide devices with a certain status, deselect the relevant checkbox.
   
   
2. By manufacturervendor, model or IP address. To do this, use the Filter field. For example, this filters the Sony devices.
   
   In addition, you can filter cameras from a subnet.
   
   

When adding a device, you can immediately set several configuration options, such as:

Manufacturer and model.

...

ID and object name.

...

Manual input of device data

If an IP device is not shown in the search results (because it is located on a different subnet or the connection with it is temporarily lost), you can add it manually. To do this, you need to select the type of IP device to be added, specify the IP address and connection port of the device, and select the vendor and model in the area with a neutral background located under the list with automatic search results.

Image Added

You can also specify the vendor and model of the device using the search in the input field.

Image Added
If the device's IP address, Port, Vendor, Username and Password are set, the device model can be automatically detected by clicking the Image Added button.

Image Added

Adding devices to the configuration

To add an IP device to a configuration:

• select a mode for adding the device to the configuration;
• specify the device settings, if necessary;
• the device is added to the configuration.

Modes for adding devices to the configuration

Three

On motion/Embedded detection – an embedded VMD tool and an automatic rule for writing to the specified archive are automatically created for the camera you are adding. By default, recording stops when an event detection is finished.

...

In addition, three modes are available for adding a device to a configuration. These are described in the following table.

...

Configuring IP device

...

1. Set device settings, if necessary.
2. Select a mode for adding the device to the configuration.
3. The device is then added to the configuration.

settings

When adding a device, you can immediately set several configuration options, such as:

• vendor and model.

• login and password.

• ID and object name.

  Info
  title Note
  The object ID can contain numbers, Latin letters and the "_" sign. Once the device is created, its short name will match the specified ID (see Camera). In this case: The camera ID cannot be changed, since it is used to maintain the connection with the archive when replacing the camera (see Saving the archive when replacing the video signal device). The short name can be changed, and the added devices will be sorted in the object tree in ascending order of this field (see Camera).

• archive selection and the recording parameters (see Configuring recording to an archive):
  1. No—camera is linked to the archive, no recording.
  2. Always—continuous recording.
  3. On motion (default)—for the camera you are adding, either an embedded motion detection (see General information about embedded detectors), or Axxon One Motion detection tool (see Configuring the Motion detector) is automatically created. An automatic rule is also created for recording to the specified archive (see Automatic rules). By default, recording stops when an event from the detection tool is finished.

     Info
     title Note
     When creating a new device, the pre-alarm time interval for video recording is automatically set to 3 seconds (see Configuring recording to an archive). The embedded motion detection is created automatically only for certain camera models. For the information about support for embedded motion detection, see the list of supported devices, the Analytics column. The embedded motion detection is configured through the web interface of a specific camera. In other cases, Axxon One Motion detection tool is created.

     
     

• device location coordinates in the format 53.212558; 50.204991 (coordinates are used when adding a camera to the map, seeAdding video cameras).

Adding devices

During a single configuration change, you can add a single device or all devices listed in the search results (other than devices for which compatibility is not guaranteed). To add one device, click the  button. To add all devices, click the Add all button.

If you set no individual access parameters while adding hardware, a dialog window appears for setting unified access parameters. 
Image Removed

If an IP device is not shown in the search results (because it is located on another subnet or contact has been temporarily lost), you can add it manually. To do so, in the neutral-colored area above the search results, select the type of IP device that you are adding (with or without edge storage), specify an IP address and port, and select the manufacturer and model.
Image Removed
Then add the device to the configuration  by following the steps described previously.

To remove a device from the search results, click the Image Added button.

If you set no individual access parameters while adding hardware, a dialog window appears for setting unified access parameters. 
Image Added

Next, the device is added to the configuration.

When you add a device to the system, the Default permissions are applied, which are configured for each role (see General information about users).

Removing IP devices

To remove IP devices, select them one or more objects in the device list (hardware tree by left-clicking one or more devices, (while holding down the CTRL Ctrl key to select multiple devices) and click the  Delete  button.If you click the IP address, you will jump to the device Web interface.