Go to documentation repository
Page History
...
Description of events of the Grabber object.
Event | Description |
"+12V" | Voltage error +12V. |
"+3.3V" | Voltage error +3.3V. |
"+5V" | Voltage error +5V. |
"-12V" | Voltage error -12V. |
"-5V" | Voltage error -5V. |
"CPU_FAN" | Number of ventilator rotations. |
"CPU_TEMP" | Temperature of processor. |
"SYS_TEMP" | Temperature of MB chipset. |
"UPS_COMMLOST" | Connection lost. |
"UPS_FATAL_ERROR" | Error of connection. |
"UPS_LOWBATT" | Battery low. |
"UPS_ONBATT" | Switch to battery supply. |
"UPS_ONLINE" | Restoring the main supply. |
"UPS_REPLACEBATT" | Battery changing is required. |
"UPS_SHUTTING" | Shutdown. |
"VCORE" | Voltage of processor core. |
"AUDIO_SIG_LOST " | Sound lost |
"CONNECT_FAIL" | Connection error |
"CONNECT_OK " | Connected |
"NETWORK_FAILURE " | Connection lost |
"STATE_CONNECTED " | Connection restored |
Operator format to describe actions with the video capture device is:
...
List of commands and parameters for the Grabber object is presented in the following table:
Command – command description | Parameters | Description of parameters |
"SETUP" – sets parameters of video capture device. | chan<> | Number of PCI slot (0,1,2,…,32). |
mode<> | Speed of grabber/digitising (0 – maximal, 1 – average, 2 – minimal). | |
resolution<> | Resolution (0– standard, frame quarter (384x288); 1 – high, half-frame (768x288); 2 – maximal frame (768x576)). | |
format<> | Format of video signal (PAL, NTSC). | |
drives<> | Disks for video archive record (DRIVE1:\, DRIVE2:\ … DRIVEN:\). | |
cams<> | Number of connected video cameras | |
auth<> |
ip<> | IP-address of video input network card | |
name<> | Name of object. | |
flags <> | Flags. | |
ip_port<> | IP-port. | |
password<> | Password. | |
type<> | Type of digitising. | |
username<> | Login. | |
watchdog<> | WatchDog shutdown (0 –disabled, 1 – enabled). | |
"SET_DRIVES" – sets disks for video archive record. | drives<> | Disks for video archive record. |
"MUX1_OFF" – disables video output through the analog output 1. | - | - |
"MUX2_OFF" - disables video output through the analog output 2. | - | - |
"MUX3_OFF" - disables video output through the analog output 3. | - | - |
"SET_IPINT_PARAM" – Sets (change) parameters of IP-device. Reaction allows changing of IP-device settings not entering its web-interface. Note. For reaction operation it is required to enable the mode of multi-flow video signal - see. Administrator's Guide, sectionConfiguration of multistream video, andAppendix 2. Defining param_id and param_value values for SET_IPINT_PARAM reaction | param_id<> | Name of parameter. Set of parameters for each camera is individual - see Appendix 2. Defining param_id and param_value values for SET_IPINT_PARAM reaction |
param_value<> | Value of parameter. Set of parameters for each camera is individual - see Appendix 2. Defining param_id and param_value values for SET_IPINT_PARAM reaction | |
cam_id<> | Camera ID in the Intellect software package. | |
vstream_id<> | Number of video-flow (optional parameter). Is given by “Number of camera”.”Number of flow”, for example 1.1, 1.2. |
Properties of the GRABBER object are shown in the table.
Properties of the GRABBER object | Description of properties |
ID<> | Object ID. |
PARENT_ID<> | Number of video capture device. |
Examples of using events and reactions of the Video capture Device object:
...
Overview
Content Tools