Page History

For the Traffic violations detection module operation program module for identifying the plates and that is being set up is required (see Activating the program module, used for identifying the plates section).

The Traffic violations detection object is created on the basis of LPR channel object.

To set Configure the Traffic violations detection module, do the following as follows:

1. Go to Traffic violations detection setting settings tab.
   

2. In Traffic lights signal dropdown list select Sensor object (see Intellect software package: Installing and configuring security system components guide) by signal of which the light of traffic light is detected (1).

   Info
   title Note.
   Information about Sensor object is presented in the Intellect software package: Installing and configuring security system components guide. Information about Traffic Light Detection is presented in The Traffic Light Detection software module setup section.

   
   

   Note
   title Attention!
   For correct operation of the Traffic violations detection module disarm the corresponding Sensor object.

   
   

3. From the Alarm direction: dropdown list select the signal of traffic light detection on which the traffic violations detection is to be responded (2).
   1. Basic - to fix violation use the base signal of the traffic light.
   2. Left - to fix violation use the left arrow of the traffic light.
   3. Right - to fix violation use the rlght arrow of the traffic light.
4. Set the Draw stop line checkbox if it's necessary to overlay a stop line before the traffic light (3).
5. Set up the stop line displaying:
   5.1 Click Stop line settings (4). The window of the same name opens.
   
   5.2 Click Stop video to set the stop line. As the result the frame on which it's necessary to set the stop line, is displayed.
   
   5.3 Set the stop line. To set the stop line, click the road edge in the image, press the left mouse button, drag the cursor to another edge of the road in the video frame.
   5.4 Click OK.

6. Set up the displaying of violation areas:
   6.1 Click Setting violation areas (5). The window of the same name opens.
   
   6.2 Click Stop video to set the violation areas. As the result the frame on which it's necessary to set the violation areas, is displayed.
   
   6.3 Set the areas corresponding to following zones: before stop line. stop line, crosswalk, crossroads. To set the violation areas, click the points corresponding to the boarder of selected area in the video frame.
   6.4 Click OK.

   Info
   title Note.
   To remove the area click the button close next to the corresponding button.

   
   

7. In the Delay in violation registering field enter time (in milliseconds) that determines the time interval after which after switching on a red light the violations will fix (6).

8. In the Time of stop for recording field enter time (in milliseconds) that determines the time interval during which the vehicle should stay still while registering the Stop over crosswalk line violation (7).

   Info
   title Note
   In case of incorrect recognition of the Stop over crosswalk line violation it is possible to change parameters of the registry keys affecting the correctness of recognition of this violation. The alarm is activated when changing parameters even if only one plate is recognized at the crosswalk (regardless of if the vehicle was moving or not) - see Registry keys reference guide. For this: Open Windows Registry Editor and go to HKEY_LOCAL_MACHINE\SOFTWARE\Wow6432Node\ITV\INTELLECT\URMLPR (1). Select and double click the Alarms.CrossWalkOne string parameter for editing (2). Set 1 in the Value data: field (3).  Click ОК (4) to save changes. Select and double click the Alarms.LimitedByBestResult string parameter for editing(5). Set 1 in the Value data: field (6). Click ОК (7) to save changes. Restart Intellect for changed parameters to become effective.

   Image Added
   Image Added

9. In the Add.photos: fielld enter the number of photos made before the licence plate fixing and after its going out the control zone (8).

10. In the Interval: field enter time (in milliseconds) that determines the time interval between saving additional photos (9).

    Note
    title Attention!
    For correct operation of synchronized frames recording set the checkbox in Automatic recording on LPR channel object setting panel and set value of time that is bigger than the product of Number of frames for saving and Interval of frame saving parameter points.

    
    

11. In the Number of pictures to trace alarm: field specify number of photos which will be stored from the moment of LP recognizing on the base recognizer to the moment of LP recognizing on the additional recognizer (10).
12. In the Additional recognizers: table specify additional LPR channels if it's required to use them along with the base recognizer (11).
    1. To add additional recognizer right-click in the Additional recognizers list, then click Add in the drop-down menu.
       
    2. From the LP recognition drop-down list select the additional recognizer (1).
       
    3. From the Sensor: drop-down list select the sensor which will send events about traffic light operation (2).
    4. From the State drop-down list select event from the sensor on which violation will be fixed (3).
    5. From the Alarm drop-down list select the corresponding type of violation (4).

    6. Click OK. The specified parameters will be added to the Additional recognizer table.
       

       Info
       title Note.
       To modidy recognizers in the rable, right-click the required recognizer to open the functional menu. Click Delete all button if the Additional recognizers table it to be cleared.

       
       

13. To save the changings click Apply.

...