To
...
configure the
...
Tampering detector, do the following:
Go to the
...
Detectors tab.
- Below the required camera, click Create… → Category: Service → Tampering
...
- detector.
By default, the detection tool detector is enabled and set to respond to all types of video analysis.
If necessary, you can change the detection tool detector parameters. The list of parameters is given in the table:
| Parameter | Value | Description |
|---|
| Object features |
| Video stream | Main stream | If the camera supports multistreaming, select the stream for which detection is needed. Selecting a low-quality video stream reduces the load on the Server |
| Other |
| Enable | Yes | By default, the |
detection tool | detector is enabled. To disable the detector, select |
the value Detection detection tool | detector name or leave the default name |
Decode key frames
| Yes | By default, the Decode key frames parameter is enabled. In this case, only key frames are decoded. To disable the parameter, select the No value.
This parameter reduces the load on the |
Serverserver, but at the same time the detection quality decreases. We recommend enabling this parameter for "blind" (without video image display) |
Serversservers, on which you want to perform detection.
For the MJPEG codec, decoding isn’t relevant, as each frame is considered a key frame. | Note |
|---|
| The Number of frames processed per second and Decode key frames parameters are interrelated. If a local |
|
Client client isn’t connected to the |
|
Serverserver, the following rules work for remote |
|
Clientsclients: - If the key frame rate is less than the value specified in the Number of frames processed per second field, the
|
|
detection tool will work - detector works by key frames.
- If the key frame rate is greater than the value specified in the Number of frames processed per second field, the detection
|
|
will be - is performed according to the set period.
If a local |
|
Client client is connected to the |
|
Server detection tool detector will always work according to the set period. After disconnecting the local |
|
Clientclient, the above rules will be relevant again. |
|
|
| No |
| Decoder mode | Auto | Select a processing resource for decoding video. When you select a GPU, a stand-alone graphics card takes priority (when decoding |
with Nvidia NVDEC | with Nvidia NVDEC chips). If there is no appropriate GPU, the decoding will use the Intel Quick Sync Video technology. Otherwise, CPU resources will be used for decoding |
| CPU |
| GPU |
| HuaweiNPU |
| Number of frames processed per second | 25 | Specify the number of frames for the |
detection tool | detector to process per second. The value must be in the range [0.016; 100] |
| Type | Tampering |
Detection detection tool | detector type (non-editable field) |
| Advanced settings |
| Blurred image analysis | Yes | By default, all types of analysis are applied to the video image. Select the No value for unnecessary types of analysis. | Note |
|---|
| If you select Compression artifacts analysis, Image noise analysis and Blurred image analysis, you must specify the values for the Event duration to trigger detection (sec), Sensitivity parameters. |
|
| No |
| Compression artifacts analysis | Yes |
| No |
| Image noise analysis | Yes |
| No |
| Quality degradation analysis | Yes |
| No |
| Scene change analysis | Yes |
| No |
| Basic settings |
| Event duration to trigger detection (sec) | 20 | Specify the maximum time of event duration for the response in seconds, after which the |
detection tool detector generates an event. The value must be in the range [5, 1200]. |
definetely - definitely detects a defect in the frame, the response from the
|
detection tool - detector comes before the specified time.
- If after the specified time, the defect hasn't been detected, you must increase the Sensitivity of the
|
detection tool |
| Sensitivity | 50 | Specify the sensitivity of the |
detection tool | detector as a percentage. The higher the sensitivity, the smaller change in the frame is detected. The value must be in the range [0, 100] |
To save the parameters of the detection tooldetector, click the Apply 
Image Modified button. To cancel the changes, click the Cancel 
Image Modified button.
Configuration of the Tampering detector is complete.
