Go to documentation repository
Page History
...
Video | |||||
Registry section | String parameter | Available values | Default | Product version | Parameter in effect |
x32: (X32)\Video | AcsStdLimit | 1-30 | 1 | 4.8.0 and later | Sets the upper limit of succession of frames in the stream in the MJPEG format. If the succession of frames sent to the remote workstation rises to the value specified in the registry key, then grooming is enabled |
x32: (X32)\Video | AcsMpegLimit | 1-30 | 25 | 4.8.0 and later | Sets the upper limit of succession of frames in the stream in the H.264/MPEG4 format. If the succession of frames sent to the remote workstation rises to the value specified in the registry key, then grooming is enabled |
x32: (X32)\Video | Activecam | 0, 1 | 1 | 4.7.3 and later | Defines whether to activate the camera by the first click |
x32: (X32)\Video | ActivateTelemetryHotkeys | 0, 1 | 0 | 4.8.2 and later | Defines whether the Telemetry control via hotkeys is activated |
x32: (X32)\Video | AdaptiveClientFrameSkip | 0, 1 | 1 | 4.8.2 and later | When the value is 0, then grooming on the Server is disabled. It is better not to disable grooming |
x32: (X32)\Video | AdaptivePlayer | 0, 1 | 0 | 4.7.6. HOTFIX build 214 and later | The key is created on the Server. It defines whether the AdaptivePlayer is enabled. When the playback speed is changed, the Client sends data about new speed to the Server. Every time there is the change the Server clears the succession of frames sent to the Client and starts creating a new one with grooming specified by the Client. Hence, the Client does not get every frame – this reduces the Server load |
x32: (X32)\Video | FastPlayStep | 1-6 | 1 | 4.8.0 and later | The key is created on the Client. It allows setting the step of playback speeding-up. Example: for the 3 value the speeding-up step is x6 (i.e. playback speed can be x6, x12, x18, etc.), for 5 – x10. Max playback speed is x60. High playback speed can be achieved when the AdaptivePlayer is enabled |
x32: (X32)\Video | allclientsbps | >=0 | 0 | 4.7.6 and later | Sets the upper limit of total outgoing video traffic: 0 – not in use >0 – max bandwidth of outgoing stream for all Video.run clients |
x32: (X32)\Video | AllowDelete | 0, 1 | 0 | 4.7.3 and later | The key allows deleting files in the archive list when clicking the Del button |
x32: (X32)\Video | AlwaysServerConnection | 0, 1 | 1 | 4.7.3 and later | Defines whether to connect the Monitor to the Server |
x32: (X32)\Video\ArchDays | <camera id> | > = 0 | 0 | 4.7.5 and later | Defines whether to store the archive of the specified camera for xxx days |
x32: (X32)\Video | ArchStatus | 0, 1 | 1 | 4.7.3 and later | Defines whether to send current archive status to the Server. This key can be used only if one disk is selected for recording the archive |
x32: (X32)\Video | ArchSync | > 0 | 1 | from 4.9.5, 4.8.10 | Defines whether data synchronization between Server and Backup archive is enabled or not. Synchronization is disabled when the value is 0. When the value is > 0 the key sets maximum imbalance of Backup archive depth between channels in minutes. By default the key is not created and its value is 1. The key must be created/modified on the computer corresponding to the Server on the basis of which the Long-term archive object is created |
x32: (X32)\Video | Cfg | - | name | 4.7.3 and later | Sets the name of configuration file |
x32: (X32)\Video | CheckLostFolders | 0, 1 | 0 | 4.7.3 and later | Defines whether to remove old log files from the oldest directory when going to a new disk |
x32: (X32)\Video | Compression | 0,1 | 1 | up to 4.8.0 | Defines whether to check and delete the folders and files that are not in the index |
x32: (X32)\Video | DebugCam.Camera_ ID | 0, 1 | 0 | 4.7.7 and later | 0 – logging is disabled 1 – logging is enabled |
x32: (X32)\Video | DecompressThread | - | - | Key is not active | |
x32: (X32)\Video | DecompressWidth<Monitor_number> | - | 4.7.3 and later | Sets the size of frame starting from which the <Monitor_number> starts partial decompression of video signal. For instance, when the value of the DecompressWidth1 parameter is 3000, the Monitor1 will not decompress all frames that are less than 3000 pixels | |
x32: (X32)\Video | Delta | 0, 1 | 1 | 4.7.3 and later | Allow sending only key frames from Server to Client
|
x32: (X32)\Video | Demo | 0, 1 | 0 | 4.7.3 and later | Defines whether the capture cards are in use or video comes from the file |
x32: (X32)\Video | DetectionFps | 0.3…30 | - | 4.7.8 and later | Sets the speed of the detector zone and the main motion detection tool in fps, i.e. the maximum number of frames processed per second by the detection tool. The lower the key value, the less frequently the frames are processed. If the key is not created, then the detection tool analyzes only reference frames. For example, if GOP (group of pictures) = 64, i.e. every 65th frame is reference, then without the registry key, the algorithm unpacks and analyzes every 65th frame. If the key value is less than or equal to the frequency of the reference frames (calculated by dividing the stream FPS by the GOP) or all frames of the video stream are reference, the detection tool will process only the reference frames with the specified frequency, which will reduce the CPU load. Otherwise, the whole stream will be decoded which will increase the CPU load. If the duration of the alarm in the zone is short, and the alarm does not have time to reach the analyzed frame, then it is necessary to increase the key value. Attention! Due to the peculiarities of the decimation algorithm, it is advisable to choose values that are multiples of the stream FPS. Examples:
|
x32: (X32)\Video | DisconnectInactive | 0, 1 | 0 | 4.8.0 HotFix | Defines whether the Monitor disconnects the gate if the screen is minimized: 1 – disconnect inactive monitors from the Servers (gates, archivers) |
| x32: (x32)\Video x64: (x64)\Video | AsyncConnection | 0, 1 | 1 | 4.8.0 HotFix | Enables asynchronous connection to the archive to reduce the Monitor start time and to make the video from cameras to appear quicker on it. 0 – synchronous connection to the archive 1 – asynchronous connection to the archive |
x32: (X32)\Video | EnableSnapShotMode | 0, 1 | 0 | 4.7.3 and later | Triggers camera in the snapshot mode, for Axis and D-link 900, operates with the delay |
x32: (X32)\Video | ExportDir | Path to a folder | moduledir + "\export" | 4.7.3 and later | Specifies the directory for saving frames from the Monitor interface—see Frame export, (but not via the Background export option—see The AviExport utility). The key is only created if the default file path is changed in the Tweaky utility (see The Settings panel of the Intellect section) |
x32: (X32)\Video | ExportTime | > = 0 | 0 | 4.7.3 and later | Specifies time (in ms) for exporting snapshot from live video into jpg |
x32: (X32)\Video | FreeMB | > 0 | 5000 | 4.9.6 and later | Specifies free space in the section while storing the archive in MB. When the limit is reached, the earliest recordings will be deleted on loop. Note. Old recordings may get deleted before the remaining disk space reaches the specified value if the disk space is less than 15000 |
x32: (X32)\Video | FreeMbCritical | >0 | 1000 | 4.9.5 and later | Specifies the remaining disk space. When the limit is reached, the archive is stored on another disk (if several disks are in use) |
| x32: (X32)\Video x64: (x64)\Video | ArchFreeMB | >0 | - | 4.8.8 and later | Specifies free space in the section while loop recording of reserve archive which is not in use for storing reserve archive and can be in use for recording temporary files. If key is not created, the value created by the FreeMB key is in use |
x32: (X32)\Video | GateNoRec | 0, 1 | 0 | 4.7.3 and later | Defines whether the gate performs recording to the archive |
x32: (X32)\Video | Hide | 0, 1 | 1 | 4.7.3 and later | Defines whether the "Hide Monitor" button is visible or hidden: 0 – hidden 1 – visible |
x32: (X32)\Video | HideMask | 0, 1 | 0 | 4.7.3 and later | Defines whether to hide the image with the mask filled with black |
x32: (X32)\Video | Hubslowspeed | 0, 1 | 0 | 4.7.3 and later | For wavehub. Affects fps. Slows down the multiplexer stepping rate |
x32: (X32)\Video | HWCompression | - | 3 | The key is not in use | |
x32: (X32)\Video | Index | - | 2 | 4.7.3 and later | Shows whether file indexing is in use. The value is not to be modified as file indexing is always in use. |
x32: (X32)\Video | IsPeriod | 0, 1 | 0 | 4.7.3 and later | Defines the period of recording to the archive: |
x32: (X32)\Video | Layout | - | - | 4.7.3 to 4.11.0 | The key cannot be modified |
| x32: (X32)\Video\Layouts x64: (x64)\Video\Layouts | layout<number> | - | - | 4.11.0 and later | The keys store info on layouts of the Video surveillance monitor. The keys cannot be modified |
x32: (X32)\Video | LH_Timeout | 5-2147483647 | 5 | 4.7.3 and later | Time in seconds on the expiry of which it is considered that there is no connection with Linux Hub. Default value – 5 seconds. Time interval is calculated by formula (LH_Timeout*1000/5) ms, for reconnections to Linux Hub: the more the value the more unlikely the video stream reconnects to LH |
x32: (X32)\Video | ManualBrightnessControl | 0, 1 | 1 | 4.7.7 | Defines the way of brightness and contrast control for IP cameras: 1 – enable the manual brightness and contrast control 0 – brightness and contrast are set in the camera interface |
x32: (X32)\Video | MaxFrames | 1500-10000 | 1500 | 4.11.0 and later | Sets the number of frames in the archive file |
| 500-10000 | 500 | 4.7.3 and later | |||
x32: (X32)\Video | Missed | 0 – 2,147,483,647 | Depends on the "mode" parameter of the video capture card | 4.7.3 and later | Sets the video digitization rate. By default the rate is the same as for the video capture card |
x32: (X32)\Video | NewCompressor | 0, 1 | 1 | 4.7.3 and later | Defines whether to use a new motionWavelet compressor: |
x32: (X32)\Video | NewMD | 0, 1 | 0 | 4.7.6 and later | Defines whether to use a new motion detection tool |
x32: (X32)\Video | Noallcamsbutton | 0, 1 | 0 | 4.7.3 and later | Defines whether to show the "All cameras" button on the screen |
x32: (X32)\Video | NoLayoutControl | 0, 1 | 0 | 4.7.5 and later | Disables F1 and F2 hotkeys (monitor ratio) |
x32: (X32)\Video | No_main_panel | 0, 1 | 0 | 4.7.3 and later | Defines whether to display control panel on the monitor |
x32: (X32)\Video | Nosign | 0, 1 | 0 | 4.7.6 and later | Disables encryption of the digital signature to the frame |
x32: (X32)\Video | OldDriver | KV1999 KV2000 KV2001 KV2002 KV2003 | Empty string | 4.7.3 and later | Support for old ISS cards |
x32: (X32)\Video | Oldxeon | 0, 1 | 0 | 4.7.6 and later | Support for old Xeon processors
|
x32: (X32)\Video | Onevideoout | 0, 1 | 0 | 4.7.3 and later | Defines whether video outs are combined on the FS6 video capture card |
x32: (X32)\Video | PostAlarmTime | >= 0 | 2 | 4.7.3 and later | Sets time (sec) on the expiry of which the alarm by detection tool on Axis IP cameras is not recorded |
x32: (X32)\Video | PreCompress | 0, 1 | 1 | 4.7.3 and later | Defines whether to compress pre-recorded video
|
x32: (X32)\Video | PrintFontSize | Any | 0 | 4.7.3 and later | Sets the font size for printing |
x32: (X32)\Video | Rbapp | - | - | 4.7.3 and later | Specifies the path to the app run by right-click in the monitor |
x32: (X32)\Video | IndexRebuilding | 0, 1 | 0 | 4.7.6 and later | Is used when index is being rebuilt. If the system detects IndexRebuilding=1 at start, then index is immediately rebuilt without trying to read idx files |
x32: (X32)\Video | RestoreMode | >=0 | 1 | from 4.7.4 HOTFIX from 4.11.2 | Before version 4.11.2 — the key defines whether the archive view mode will be exited when the timeout is reached (10 minutes of inactivity): 1 – in 10 minutes the archive will be exited 0 – the archive will not be exited. Starting from version 4.11.2 — the key enables to set the time period in seconds, after which the archive view mode will be exited if idle. For example, if you set 60, then the archive will be exited 1 minute after the last action with it. If the key is absent or value is 0, then the archive will not be exited |
| xx32: (X32)\Video x64: (x64)\Video | restorezoom | >=0 | 0 | from 4.11.2 | Specifies the amount of time, in seconds, after which the video scaling is reset if idle. If the key is absent or the value is set to 0, then the scaling will not be reset |
x32: (X32)\Video | ShowDate | 0, 1 | 0 | from 4.7.3 to 4.8.6, from 4.10.5 | Defines whether to show the date on the video (next to the time) |
x32: (X32)\Video | ShowID<Monitor_number> | 0, 1 | 1 | 4.9.0 to 4.10.1 | Defines whether to show the Camera ID on the button to open Camera context menu. Example: ShowID3=0 – the camera number will not be displayed in context men for the third Monitor |
x32: (X32)\Video | ShowName<Monitor_number> | 0, 1 | 0 | 4.7.3 to 4.10.1 | Defines whether to show the Camera name on the monitor |
x32: (X32)\Video | ShowTime<Monitor_number> | 0, 1 | 1 | 4.7.3 to 4.10.1 | Defines whether to show the Time on the monitor
|
x32: (X32)\Video | ShowTitle | 0, 1 | 0 | 4.7.3 to 4.10.1 | Defines whether to show the monitor name instead of the time on the control panel |
x32: (X32)\Video | ShowButtons<Monitor number> | 0, 1 | 1 | 4.10.0 to 4.10.1 | Sets if the buttons of camera number are displayed on the Surveillance monitor <Monitor_number>. If the monitor number is not specified, the buttons are not displayed on all monitors |
x32: (X32)\Video | ShowBorder<Monitor_number> | 0, 1 | 1 | 4.10.0 to 4.10.1 | Sets if the borders are displayed around the Surveillance monitor <Monitor_number>. If the monitor number is not specified, the border is not displayed on all monitors |
x32: (X32)\Video | SnapShotTime | > 0 | 1 | 4.7.3 and later | Sets time (sec) between snapshots |
x32: (X32)\Video | TMDCorrellation | 1-100 % | 30 | 4.7.6 and later | Permissible minimum similarity between frames when they are considered to coincide. 100% for completely identical frames |
x32: (X32)\Video | TMDNonCorrectionStop | > = 0 | 1 | 4.7.6 and later | Number of incoming frames from PTZ camera upon STOP command; the decision to stop pointing (if there is no command to start motion) is made |
x32: (X32)\Video | TMDSpeedCutoff | 0..∞ | 15 | 4.7.6 and later | Sets the limiting value of speed for camera with automatic centering |
x32: (X32)\Video | TMDTolerance | - | 50 | 4.7.6 and later | Sets pointing accuracy (zone of tranquility). Corresponds to the value of area around stop point of PTZ camera (px) |
x32: (X32)\Video | UseConfigureByWeb | 0, 1 | 0 | 4.7.3 and later | Defines whether to use IP camera settings. When this key is enabled, the driver will try not to change parameters set on the camera. But behavior depends on specific camera+driver version+firmware combination |
x32: (X32)\Video | UseCompression | 0, 1 | 1 | 4.7.3 and later | Defines whether video compression is in use (UseCompression.camera ID) |
x32: (X32)\Video | UseLowRefFramesFpsFix | 0, 1 | 1 | 4.7.8 and later | Enables stream decompression with low key frame FPS. Threshold FPS value = 2 |
x32: (X32)\Video | VideoDumpMode | 0, 1, 2 | 0 | 4.7.8 and later | Sets the mode of video dump: |
x32: (X32)\Video | VideoDumpPath | - | Intellect/ FrameDump | 4.7.8 and later | Path to the folder where frames are stored |
x32: (X32)\Video | AdaptiveStream | 0, 1 | - | 4.8.3 HotFix | The key can be used with NON-multistream cameras only. 1 – video stream is transmitted over the network if video from this camera is required. If video is not displayed on the Client, then the there is no stream from the camera and the network is not loaded. Important! When the value of the key is 1, video is not recorded to the archive when the Video surveillance monitor is hidden. But recording is not stopped. In the result video archive fragment the period over which the Video surveillance monitor was hidden will look like a freeze frame. 0 – video stream is transmitted over the network regardless of whether video from this camera is required or not |
x32: (X32)\Video | ExtractWidth | 0, 1 | - | 4.8.4 and later | 0 – partial decompression for MotionWavalet is disabled (stream from cameras is enhanced) 1 – partial decompression is enabled |
x32: (X32)\Video | TelemetryMouseWheel | 0, 1 | - | 4.8.4 and later | 0 – digital image zooming and Telemetry zoom are performed using the mouse as described in ‘Intellect software package. Operator guide’. 1- digital zooming is performed scrolling the mouse wheel and pressing the Ctrl key. Telemetry zoom is controlled using the mouse wheel: when the wheel is scrolled, ZOOM_IN(ZOOM_OUT) commands are performed; the last mouse click performs ZOOM_STOP command |
x32: (X32)\Video | ExportFontAdaptive | 0, 1 | - | 4.8.7 and later | The key sets the relative font size for titles (including camera No. and time) when the frame or archive fragment (since 4.10.5) is exported: 0 – by default (no key). The size of titles stays the same when the frame is exported (regardless of resolution) as set in the Captioner object |
x32: (X32)\Video | ClientArchMessage | 0, 1 | - | 4.9.0 and later | The key is in to enable the following events for MONITOR object: ARCH_ENTER – enter the archive |
x32: (X32)\Video | DrawDetectorNumbers | 0, 1 | - | 4.8.7 and later | 0 – identifiers of tracking objects are not displayed in the viewing tile (by default) 1 – identifiers of tracking objects are displayed in the viewing tile |
x32: (X32)\Video | DrawDetectorColors | 0, 1 | - | 4.8.7 and later | The key sets the color of the frame that marks out the tracking object in the viewing tile: 0 – the color according to the Monitor object settings (only white color was available before Intellect 4.11.2 version) 1 – the color is calculated as the mean value in the area marked out with a frame |
x32: (X32)\Video | FaceCamOffset | 0-2147483648 | 50000 | 4.8.8 and later | The key sets the maximum camera identifier in the system. The camera will not work if its ID is greater than the value specified in the key. Values greater than maximum key value are used for the face detection tool |
x32: (X32)\Video | FontCamNameHeight | >=10 | 10 | 4.8.8 and later | The key specifies the font size of the camera name when displaying it on the Video surveillance Monitor |
x32: (X32)\Video | FontCamTimeHeight | >=10 | 10 | 4.8.8 and later | The key specifies the font size of the camera time when displaying it on the Video surveillance Monitor |
x32: (X32)\Video | ShowFileNameInTitles | 0, 1 | 0 | 4.9.0 and later | The key is used to add the name of the file to the titles using the virtual video device: 0 – the name of the file is not shown in the titles 1 – the name of the file is shown in the titles (the Captioner object is to be created) |
x32: (X32)\Video | CorrectFrameNumber | 0, 1 | 1 | 4.9.0 and later | 1 – key redefines frame numbers when archive is played back by Axxon_player.exe if frames are recorded to the archive with incorrect number 0 – key in not active, frames are played in the order corresponding to their numbers in archive |
x32: (X32)\Video | DisappearedAlarmDuration | >0 | 15 | 4.9.0 and later | Key specifies time-out in seconds after which “Disappearance in zone” detection alarm is discarded |
x32: (X32)\Video | LongInZoneTimeout | >0 | 10 | 4.9.0 and later | The key sets the time in seconds which defines the time the object stays in the zone, after which the NeuroTracker VMDA detection tools with the Staying in the area for more than 10 sec detector type, created under the Tracker object, are triggered |
x32: (X32)\Converter | CheckCompressedSize | 0, 1 | 1 | 4.9.0 and later | The key allows decreasing time of exporting video in the avi format using the Converter.exe. utility. If the key value is 0, then resolution check is disabled when exporting video in the avi format. If resolution check is disabled, then frames are not decompressed when being exported, but when resolution is changed, video artifacts can appear |
| x32: (X32)\Video x64: (x64)\Video | MonitorFrameBuffer | >=0 | - | 4.8.2 and later | The key specifies the number of frames to buffer when displaying live video from IP cameras. The value of 5 is recommended. The key is applied to decompressed video. The key is mutually exclusive with MonitorSynchronizedFrameBuffer, i.e. only one of them can be in use at a time |
| x32: (X32)\Video x64: (x64)\Video | BoardFX4MaxChannels | 0, 1 | 0 | 4.9.0 and later and later | The key enables channel limitation for FX4 card. 1 – the limitation is enabled. It is not possible to set the channel number that is bigger than it is provided by the card 0 or no key – the limitation is disabled |
| x32: (X32)\Video x64: (x64)\Video | BoardFS6MaxChannels | 0, 1 | 0 | 4.9.0 and later | The key enables channel limitation for FX6 card. 1 – the limitation is enabled. It is not possible to set the channel number that is bigger than it is provided by the card 0 or no key – the limitation is disabled |
| x32: (X32)\Video x64: (x64)\Video | TelemetryZoomStopTime | >0 | 1000 | 4.9.1 and later | The key specifies the value of optical zoom duration (delay) in milliseconds |
| x32: (X32)\Video x64: (x64)\Video | OnvifCompatibilityMode | 0, 1 | 0 | 4.9.1 and later | The key is for operation of cameras via the ONVIF protocol in the compatibility mode. It is used when the ONVIF protocol is partially supported by the camera. The key enables the compatibility mode for all cameras in the system |
| x32: (X32)\Video x64: (x64)\Video | TelemetryPointAndClickDelay | >0 | 500 | 4.9.2 and later | Sets the interval (in milliseconds) between sending Point&Click commands when controlling PTZ via surveillance monitor by clicking and holding left mouse button and the Ctrl key. See details in Operator's Guide |
| x32: (X32)\Video x64: (x64)\Video | m_nCurVolume[FS] | >=0 | 0 | 4.7.6 and later | The parameter is used for loop recording of Server archive in order to store the number of current disk for recording. The figures in ascending order correspond to the letters of the sections (e.g., 0=C, 1=D, 2=E etc.). If the parameter has not been created, then it is created at the moment of selecting the disk for recording the archive with the value of disk number which has the latest recorded archive fragment. When filling the disk, the parameter increases by 1 |
| x32: (X32)\Video x64: (x64)\Video | m_dwTime[FS] | Date in YYYY.MM.DD.HH.MM.SS format | 1970.01.01.03.00.00 | 4.7.6 and later | The parameter is used for loop recording of Server archive. If the parameter has not been created, then it is created at the moment of selecting the disk for recording with the default value. When going to the new disk, the parameter value changes as follows:
The recording will be performed on the current disk until the file with the date specified in the m_dwTime[FS] key becomes an old one on this disk (if the disk wasn’t primarily empty) or until the remaining free space on the disk becomes equal to that specified by the user (if the disk was primarily empty, see The settings panel for the Video subsystem section). Further the system will erase this file and go to the next disk |
| x32: (X32)\Video x64: (x64)\Video | m_nCurVolume[ARCH] | >=0 | 0 | 4.7.6 and later | The parameter is used for loop recording of Backup archive. The parameter is similar to the m_nCurVolume[FS] parameter |
| x32: (X32)\Video x64: (x64)\Video | m_dwTime[ARCH] | Date in YYYY.MM.DD.HH.MM.SS format | 1970.01.01.03.00.00 | 4.7.6 and later | The parameter is used for loop recording of Backup archive. The parameter is similar to the m_dwTime[FS] parameter |
| x32: (X32)\Video x64: (x64)\Video | TelemetryMouseZoom | 0, 1 | 1 | 4.9.2 and later | The key allows disabling the control of optical zoom function by mouse buttons. 0 – control of optical zoom by means of long pressing of left or right mouse buttons is not functioned 1 – control of optical zoom by means of long pressing of left or right mouse buttons is functioned |
| x32:(X32)\Video\RTSPTimeout x64:(x64)\Video\RTSPTimeout | < camera manufacturer > | 0-100 | 10 | DriverPack 3.2.26.1489 and later | Sets max. time interval at the end of which the following frame is sent through the video gate. Example: in order to limit the frame rate (to 0,01) of the stream transmitted through the video gate using the RTSP protocol, the "RTSP" parameter is to be created with value 100 |
| x32: (X32)\Video x64: (x64)\Video | UnlimitMonitorSize | 0, 1 | 0 | 4.9.3 and later | When the value=1, the key removes restrictions on the Monitor height and width. When the large size (more than 900%) is set for the Monitor window, then proper operation of Intellect is not guaranteed |
| x32: (X32)\Debug x64: (x64)\Debug | ShowDisplayingFps | 0, 1 | 0 | 4.9.3 and later | When the value = 1, the key enables displaying information on FPS in the first line of captions on the video image in the Viewing tile. Since version 4.11.0 the name of streaming, codec, resolution (not necessarily displayed on the screen), bitrate, key frame rate (each value in a separate line) can also be displayed. Note.If the debug mode is enabled, the fps of the digitized video signal is displayed on the Monitor (see Frame rate settings), i.e. the key allows comparing these values. The Camera-based Captioner object is to be created in order to use this function |
| x32: (X32)\Video x64: (x64)\Video | StartPlayFromPFrame | 0,1 | 1 | 4.9.3 and later | After using frame-by-frame reverse playback, when returning to the normal playback mode: 0 – playback starts from the nearest previous key frame 1 – playback starts from the nearest previous key frame (difference, R frame) |
| x32: (X32)\Video x64: (x64)\Video | UseServerTime | -1 * all empty value Comma-separated IDs of cameras in Intellect Note. Use all instead of * value in versions up to 4.9.8 | - | 4.9.3 and later | Camera sets time of frame while video image transmission after which frames playback by turn depending on the time of frame. Sometimes camera sets incorrect time, so frames playback in invalid order because of bad communication quality or time of camera is not synchronized with server. The key sets list of IP-cameras for which time of frame will be set according to system time of the Intellect server while reading frames from the network. Possible values: -1, *, all or empty value (the key is not created) – the server time is applied for all cameras on the server (default starting from Intellect 4.10.0) Comma-separated IDs of cameras – the server time is applied for specified cameras while disabled for the rest of the cameras. Note. The key can be used for cameras with absolute time (e.g. Tattile cameras). Other cameras synchronize with server time on default. Example. When the value of registry key is “1,10,135”, time of Server will be applied on cameras 1, 10 and 135 |
| x32: (X32)\Video x64: (x64)\Video | MxpegResetCounter | >=0 | 13 | 4.9.5 and later DP 3.2.30 | The key sets the number of key frames decompressed by MxPEG decompressor before they are returned. The waiting period of specified frames is 3 minutes, on the expiry of this period the decompressor is reinitialized. The key is in use if there is no video in Intellect when MxPEG codec operates with MxPEG decompressor. In this case the value of the key is to be reduced |
| x32: (x32)\Video x64: (x64)\Video | TelemetryMouseAlternative | 0, 1 | 1 | 4.9.5 and later | 0 – previously used Mouse PTZ control mode is in use 1 – a new Mouse PTZ control mode is in use. See Mouse PTZ control |
| x32: (X32)\Video x64: (x64)\Video | TelemetryLineColor | 4-byte RGB value Most significant byte – 4 = 0. byte 3 – R (0..255) byte 2 – G (0..255) byte 1 – B (0..255) Examples: blue color: LetterboxBackgroundColor = 255 white color: LetterboxBackgroundColor = 16777215 | 16777215 (white color) | 4.10.4 and later | The key sets the color of the crosshair and the arrow line during PTZ control. See Mouse PTZ control |
| x32: (x32)\Video x64: (x64)\Video | ContinousMode | Identifiers of cameras, divided by comma, for which continuous PTZ mode is enabled. Example: 2,3,1 | - | 4.9.5 and later | In the Continous mode camera lens is re-focused slowly – arrow indicating the re-focus direction smoothly follows the pointer. To use the Continous mode, the camera is to support this mode. In discrete mode (if the camera number is not specified in the key) re-focus of the camera objective depends on the area of the mouse click |
| x32: (x32)\Video x64: (x64)\Video | MonitorSkipArchFramesEnable | 0, 1 | 1 | from 4.9.5 to 4.9.7 from 4.10.1 | The key enables frame skipping while playing back the archive. 0 – all frames are displayed. If there is lack of resources, video delays and loss of synchronization with sound are possible, and the playback speed can be increased no more than 4 times (or no more than 60 FPS) 1 – only key frames are played back forward at rate x12 and faster and backwards at rate x8 and faster. Note. See also info on FastPlayMpegSkip andMonitorForwardSkipSpeed registry keys |
| x32: (X32)\Video x64: (x64)\Video | ResetOSDLine | 0, 1 | 0 | 4.9.7 and later | The key is for enabling and disabling titling on the video image using the SC590N4 video capture device. 0 – OSD-captions of device are in use 1 – OSD-captions of device are not in use Note. Restart of operating system can be required to apply settings while changing the key value |
| x32: (x32)\ x64: (x64)\ | ClearProtocolFromCurrentTime | 0, 1 | 0 | 4.9.8 and later | The key is for changing the way of deleting archive of events at the end of storage period (see Configuring events logging): 1 – storage period is counted from the current PC time. So if there are events "from the future" (date of which is later than the current date) in the archive of events, they are neither taken into account when deleting old entries nor deleted 0 – storage period of records is counted from the date of creation the newest record Note. Deletion is performed at 00:00:00 in case of active license |
| x32: (X32)\Video\AVI x64: (x64)\Video\AVI64 | SubtitlesFontSize | 8 – 48 | - | 4.9.0 and later | Font size of captions with camera name and time while export from the Monitor. Note. Captions overlaid using the Captioner object are configured separately on the settings panel of the Captioner object |
| x32: (x32)\Video x64: (x64)\Video | TelemetryArrowLen | 0 – 100 | 50 | 4.9.8 and later | The key specifies length of the arrow displayed on the video image at mouse PTZ control from the Monitor window. Arrow length is set in percent and counting from the end |
| x32: (x32)\Video x64: (x64)\Video | TelemetryStopZone | 2 – 100 | 50 | 4.10.0 and later | The key sets the size of the zone in the center of the video where PTZ control functions using mouse are disabled. The less the key value the bigger the “dead” zone. The default value corresponds to the size of the cross in the center of Surveillance monitor during PTZ control |
| x32: (x32)\Video x64: (x64)\Video | ShowTelemetryCross | 0, 1 | 1 | 4.10.0 and later | The key is designed to enable and disable showing a cross in the center of Surveillance monitor during PTZ control. 1 – the cross is shown in the center of Surveillance monitor during PTZ control 0 – the cross is not shown in the center of Surveillance monitor during PTZ control |
| x32: (x32)\Video x64: (x64)\Video | GreenStreamUpdateTimeoutMS | >0 | 20000 | 4.10.0 and later | The key sets time in milliseconds that equals to stream scan rate in order to optimize connection parameters. This key can be active only if the Video stream setting checkbox is set (see Configuration of multistream video) |
| x32: (x32)\Video x64: (x64)\Video | TitlesOnlyArchive | 0, 1 | 0 | 4.10.0 and later | The key is designed to enable saving titles separately from video. 1 – titles are saved in files of *.t01 type separately from video. If there is time stamp in the titles, then these titles are not displayed in live video, but can be seen in the archive (for the corresponding period of time). Titles with no time stamp are displayed on live video 0 – titles are saved with video and are displayed on live video |
| x32: (x32)\Video x64: (x64)\Video | ExportDirFixed | 0, 1 | 0 | 4.9.9 and later | The key allows forbidding change of export catalogue when the archive period is exported and when the archive is exported using the AviExport utility. 1 – export catalogue change is forbidden 0 – export catalogue change is allowed |
| x32: (x32)\Video x64: (x64)\Video | ShowBookmarkButtons | 0, 1 | 1 | 4.10.1 and later | The key is used to disable creating and editing of bookmarks meant for protection against video rewriting (see Create a bookmark). 1 – show Create and View bookmarks buttons 0 – hide Create and View bookmarks buttons |
| x32: (x32)\Video x64: (x64)\Video | ShowExportButtons | 0, 1 | 1 | 4.10.1 and later | The key is used to disable export of bookmarks meant for protection against video rewriting (see List of bookmarks). 1 – show bookmark export button 0 – hide bookmark export button |
| x32: (x32)\Video x64: (x64)\Video | ResizePrintingFrame | 0, 1 | 0 | 4.10.1 and later | The key sets the width of frame for printing: 1 – the frame is printed out so that is fits the full width of the page depending on the default layout (portrait or landscape) 0 – the frame is printed out not on the whole page |
| x32: (x32)\Video x64: (x64)\Video | CycleByLayouts | 0, 1 | 0 | 4.10.1 and later | The key enables paging by layouts in the Surveillance Monitor instead of the standard scrolling of Surveillance Windows. 0—standard scrolling. 1—paging by layouts. The key must be created on the computer where the Surveillance Monitor is displayed. Attention! If you set CycleByLayouts=1 key and then change the Quad splitter settings in the Surveillance Monitor, they will be ignored. If the Quad splitter has already been configured and the CycleByLayouts=1 key is set, then the Quad splitter settings will be applied until you enable automatic scrolling, after that they will be ignored |
| x32: (x32)\Video x64: (x64)\Video | EnableCodecSettings | 0, 1 | 0 | 4.10.1 and later | The key is in use for enabling compressor and decompressor on the settings panel of the Camera object. 0 – Compressor and Decompressor parameters are not available for changing 1 – Compressor and Decompressor parameters are available for changing |
| x32: (x32)\Video x64: (x64)\Video | PerspMaxObjects | >0 | 10 | 4.10.1 and later | The key sets maximum calibration objects and background points that can be used when configuring perspective for the Tracker object (see Configuring perspective) |
| x32: (x32)\Video x64: (x64)\Video | VirtualGrabberSortMode | 0, 1, 2 | 0 | 4.10.1 and later | The key sets the order of playing back files when the virtual grabber is in use: 0 – sorting by the latest modification1 – sorting by name (lexicographic) 2 – sorting by creation time |
| x32: (x32)\Video x64: (x64)\Video | NotifyAbout_arch_days | 0, 1 | 1 | 4.10.2 and later | The key allows disabling the warning when the Store no less than parameter is set for more than 30% of cameras in the system(see also The Settings panel of the Camera object) |
| x32: (x32)\Video x64: (x64)\Video | archrecrestart | 0, 1 | 0 | 4.8.3 to 4.10.3 | Enables restarting record on archive entering. 1 – patch that has been recorded on archive entering is stopped and a new one starts. As a result the user who enters the archive sees a freeze frame corresponding to that on exiting 0 – recording is not stopped on archive entering The key is to be created on a Server |
| x32: (x32)\Video x64: (x64)\Video | MonitorArchPrevTimeSeconds | >=0 | -1 | 4.10.4 and later | Enables restarting record on archive entering and sets time period in seconds (0 or more) to roll back from current time at archive entering and start playback from. All frames are forced to be recorded to the disk at archive entering, taking into account the pre-alarm recording. -1 – disabled (by default). Note. The key should be created both on the Server and on the Remote Client where you want to use it. If the key is set to "0", it works in the same way as archrecrestart set to 1(see above). If "1", "2", etc. is set, the key works in the same way as archrecrestart set to 1, plus the time for positioning in archive is set. Note. If every 20th frame is a key frame, entering archive can take up to 2-4 sec, as all frames are warranted to be recorded on disk yet it is possible only if the key frame for the next clip is received in order to avoid gaps in the archive |
| x32: (x32)\Video x64: (x64)\Video | archenterpause | 0, 1 | 0 | 4.8.3 and later | Enables pausing playback on archive entering. 1 – the Pause button is pressed on archive entering, archive navigation using arrow keys 0 – the Pause button is not pressed on archive entering The key is to be created on a Server |
| x32: (x32)\Video x64: (x64)\Video | LButtonClickContinuousPlayEnable | 0, 1 | 0 | 4.10.3 and later | The key changes the playback by alarms control mode in the Video surveillance monitor: 0 – long left-click starts continuous playback of archive fragments, short click starts playback of the current selected archive recording only 1 – long left-click starts playback of the current selected archive recording only, short click starts continuous playback of archive fragments |
| x32: (x32)\Video x64: (x64)\Video | MonitorPlaybackControlByMouseWheel | 0, 1 | 0 | 4.10.3 and later | The key enables control of the playback speed of the archive in the Video surveillance monitor and pausing/resuming playback using the mouse wheel. 0 – playback speed control using the mouse wheel is possible only when the cursor is hovered over the playback control panel. When hovering the cursor over the video, the mouse wheel controls the zoom. Clicking on the mouse wheel is used to control the telemetry (autocentering) 1 – playback speed is adjusted using the mouse wheel while hovering the cursor over the Surveillance window. Clicking the mouse wheel pauses/resumes video playback Note. See Video playback controls section in Operator's Guide |
| x32: (x32)\Video x64: (x64)\Video | ConnectOnlyByClient | 0, 1 | 0 | 4.10.3 and later | The key disables video data transmission from the Server to the Videogate when video data via this Videogate is not requested on the Clients. The key is to be created on the computer under which the Videogate object is created. 0 – video is transmitted from the Server to the Videogate constantly 1 – video is transmitted from the Server to the Videogate when video data via this Videogate is requested on the Client. If recording to Videogate archive is configured, then to disable video data transmission from the Server to the Videogate, when they are not requested on the Clients, the Active cameras recording checkbox is to be set checked on the settings panel of the Videogate object (see Configuring the recording to the Videogate archive). If this checkbox is set unchecked and recording to the Videogate archive is configured, then video data is transmitted to the Videogate constantly |
| x32: (x32)\Video x64: (x64)\Video | MaximizeCameraOnDblClk | 0, 1 | 0 | 4.10.3 and later | The key enables transforming the Surveillance window into a one-fold layout by left double-clicking. The key is created on the computer where the video is displayed and the described behavior of the Video surveillance monitor is required. 0—by left double-clicking the size of the Surveillance window is increased by one fold 1—by left double-clicking the size of the Surveillance window is increased to a one-fold layout (only the selected Surveillance window is displayed in the Video surveillance monitor). Right double-clicking on the Video surveillance monitor restores the original layout Note. In order for the original layout to be restored by left clicking, this key should be used together with MinimizeCameraOnDblClk |
| x32: (x32)\Video x64: (x64)\Video | MinimizeCameraOnDblClk | 0, 1 | 0 | 4.10.3 and later | The key is used together with the MaximizeCameraOnDblClk = 1 key and it enables returning to the original layout after enlarging the video surveillance window by left double-clicking. The key is created on the computer where the video is displayed and the described behavior of the video surveillance monitor is required. 0 – returning to the original layout is performed by right-clicking the Surveillance window 1 – returning to the original layout is performed by left-clicking the Surveillance window |
| x32: (x32)\Video x64: (x64)\Video | UseOneClkToMaximizeOrMinimizeCamera | 0, 1 | 0 | 4.10.5 and later | The key is valid only if both keys MaximizeCameraOnDblClk and MinimizeCameraOnDblClk are set to 1. Enables the enlargement and reduction of the Surveillance window with one left or right mouse click: 0 – enlargement of the Surveillance window and return to the original layout by double-clicking the left or right mouse button 1 – enlargement of the Surveillance window and return to the original layout by one left or right mouse click |
| x32: (x32)\Video x64: (x64)\Video | ContourAlways | *, all, IDs of cameras, comma-separated | - | 4.10.3 and later | The key enables permanent outlining of moving objects on the video from the specified video cameras on all Video surveillance monitors to which it is added. The key is not created or created with an empty value – outlining is enabled by the Operator in the Surveillance window (see Outlining of moving objects). * or all – the permanent outlining of moving objects on all video cameras in on all Video surveillance monitors is enabled. Camera identifiers comma-separated (for example, "1,2,4") – permanent outlining of moving objects is enabled for cameras with the specified identifiers |
| x32: (x32)\Video x64: (x64)\Video | savemode | 0, 1 | - | 4.10.3 and later | The key allows not changing the video surveillance mode of the active camera (archive or live video) when changing the layout and adding or removing cameras to the Video surveillance monitor. 0 – when adding a new camera to the Video surveillance monitor and when removing cameras from it, the active camera switches into the live video viewing mode 1 – when adding a new camera to the Video surveillance monitor and removing the cameras from it, the active camera does not change the video surveillance mode (archive or live video) |
| x32: (x32)\Video x64: (x64)\Video | GateDumpConnections | 0, 1 | 0 | 4.10.4 and later | Enables the archive broadcasting through the video gateway. 0 – archive broadcasting through the video gateway is disabled 1 – archive broadcasting through the video gateway is enabled |
| x32: (x32)\Video x64: (x64)\Video | clean_object_lists | 0, 1 | 0 | 4.10.4 and later | The key defines if it is necessary to delete cameras from Video Surveillance Monitor list when the Camera object is deleted. 1 – the Camera is deleted from the Monitor list on deletion 0 – the Camera is not deleted from the Monitor list on deletion. If the Camera object with the same ID is created again, it automatically appears in the Monitor list |
| x32: (x32)\Video x64: (x64)\Video | ShowDisconnectState | 0, 1 | 0 | 4.10.4 and later | The key enables displaying a message about a connection failure instead of the last frame received. 0 – When the connection to the camera is lost, the last received frame is displayed in the Surveillance window 1 – When the connection to the camera is lost, an image showing the disconnected state is displayed in the Surveillance window |
| x32: (x32)\Video\Deinterlace x64: (x64)\Video\Deinterlace | <monitor_id>.<camera_id>, e.g. 4.1 – camera 1 on monitor 4. | 1, 2 | - | 4.10.4 | The key sets deinterlacing mode for the specified camera. By default, the key is not created and mode 1 is in use. In case if it is not productive enough, for example for Paxton intercoms, use mode 2 |
| x32: (x32)\Video x64: (x64)\Video | MonitorMultiDecompress | 0, 1, 2 | 1 | 4.10.4 4.11.2 and later | The key sets the mode of using processor threads for decompression of archived video. This setting is used to increase the speed of archive video playback. 0 – Only one processor thread is used for archived video decompression regardless of the number of simultaneous archive views from different cameras 1 – A separate processor thread is used for archived video decompression for each camera, if possible. If the archive is viewed simultaneously from several cameras, the number of which exceeds the number of processor threads, then the video for several cameras will be decompressed in the same stream 2 – All available processor threads are used for archived video decompression, but only when the archive is viewed from one camera. If the archive is viewed simultaneously from several cameras, then the behavior will correspond to the key value 1 Note. If Clients are present in configuration, set the key both on Intellect Server and Client side |
| x32: (x32)\Video x64: (x64)\Video | DisableReplaceCam | 0, 1 | 0 | 4.10.4 and later | The key can be created to prohibit moving the Video Surveillance Windows on the layout in the Video Surveillance Monitor (either when the Control Panel is enabled or disabled). 0 – changing the position of the Video Surveillance Windows on the layout is allowed 1 – changing the position of the Video Surveillance Windows on the layout is prohibited |
| x32: (X32)\Video x64: (x64)\Video | EnterEdgeStorageDirect | 0, 1 | 0 | 4.10.4 and later | The key enables the user redirection to the "edge storage" after pressing the Enter archive button. 0 – after pressing the Enter archive button, the user is redirected to the video archive 1 – after pressing the Enter archive button, the user is redirected to the "edge storage" if there is one, and if it is connected to the camera in the Video Monitor The key should be specified on those computers where this option is required |
| 4.10.5 and later | The key ALSO enables the user redirection to the external archive on pressing the Tab hotkey in the Video Monitor | ||||
| x32: (X32)\Video x64: (x64)\Video | TouchScreeenUpdateTimeout | > = 0 | 0 | 4.10.5 and later | The key sets the Play button hold time in milliseconds to enable the continuous video archive playback on the touch screen |
| x32: (X32)\Video x64: (x64)\Video | ShowNoDiscIconInMonitor | 0, 1 | 1 | 4.10.5 and later | Using this key you can hide the "no disk" icon from being displayed in the Monitor if no disk is selected for recording. 0 – if no disk is selected for recording, the "no disk" icon is not shown 1 – if no disk is selected for recording, the "no disk" icon is shown in the Monitor Note. You should use this key on all computers where the "no disk" icon has to be hidden from being displayed in the Monitor |
| x32: (X32)\Video x64: (x64)\Video | DisableTelemetryOnDeactivate | 0, 1 | 0 | 4.10.5 and later | 0 – if enabled, PTZ control remains active after you hide its window or switch to another screen 1 – if enabled, PTZ control becomes inactive after you hide its window or switch to another screen; you can re-activate it manually Refer also to Mouse PTZ control |
| x32: (x32)\Video x64: (x64)\Video | nosynt | 0,1 | 0 | 4.10.5 and later | This key disables ActiveX's (refer to CamMonitor.ocx ActiveX Control) video stream recalculation to fit the display window and forces video display in its native resolution. Therefore, when you export a frame from an ActiveX window called from the Event Log or the Web Reports subsystem, you'll get full resolution frame from either live video or stored footage. 0 – ActiveX optimizes the video resolution to its window size 1 – ActiveX displays video in its native resolution |
| x32: (x32)\Video x64: (x64)\Video | ApplyChinaEastWestFix | 0, 1 | 0 | from 4.10.5 | This key allows flipping the camera icon on the map while you rotate it. 0 – standard behavior 1 – the Map receives panning value as CAM|XXXX|UPDATE_ABSOLUTE which flips the camera icon while you rotate it |
| x32: (x32)\Video x64: (x64)\Video | UseNuma | 0, 1, 3 | 0 | from 4.10.5 from 4.11.2 | This key affects the allocation of virtual memory in multi-CPU systems. 0 – uniform allocation of virtual memory 1 – NUMA allocation for optimal distribution of CPU load between multiple CPUs within a PC. Special Win32 API functions designed to work in NUMA mode are used 3 – NUMA allocation for optimal distribution of CPU load between multiple CPUs within a PC. An allocator with deferred deletion is used Note. Before changing this key, please consult your AxxonSoft manager |
| x32: (x32)\Video x64: (x64)\Video | MonitorForwardSkipSpeed | >0 | 12 | 4.10.4 and later | The key operates together with the MonitorSkipArchFramesEnable key (see above). It enables the accelerated playback on reference frames after the specified speed during the 1-camera playback. If the odd number is set as the key value, then the accelerated playback on reference frames will start at an even speed, minus 1 from the entered number |
| x32: (x32)\Video x64: (x64)\Video | NoSaveTitles | 0, 1 | 0 | 4.10.5 and later | The key disables storing captions in the captions database: 0 – the captions are saved in the captions DB 1 – the captions are not saved in the captions DB |
| x32: (x32)\Video x64: (x64)\Video | <Grabber name.MaxChannels> For example: RTSP.MaxChannels, HikVision(h.264).MaxChannels Note. Both new and old grabber names are supported. The comparison is case sensitive. | >0 | - | 4.10.4 and later, and DP 3.52.2423 and later | The key sets the maximum number of camera channels under the manually created Video Capture Device object for the specified device (grabber). By default, the maximum number of channels is 64 |
| x32: (x32)\Video x64: (x64)\Video | MaxSpeedValue | Integer | - | 4.10.5 and later | The key sets the limit on the maximum archive playback speed in the Video Surveillance Monitor both forward and reverse. Examples of values: With a value of 6, the maximum possible playback/rewind speed is x6. |
| x32: (x32)\Video x64: (x64)\Video | DecompressorTimeout | >0 | 30 | from 4.10.5.3952 to 4.10.5.3958 | Sets the time period in milliseconds that the decompressor is allowed to spend on decompression of 1 frame. If the time is exceeded, frame drops begin |
| x32: (x32)\Video x64: (x64)\Video | DecompressorQueue | >0 | 30 | from 4.10.5.3958 to 4.10.5.4075 | Sets the size of the display buffer in frames. For example, with the default value, frame skipping begins if there are more than 30 frames in the display queue for a channel. The key is applied to the compressed video |
| - | from 4.10.5.4075 | Only works when DecompressorQueue.ByTime=0 (see below) | |||
| x32: (x32)\Video x64: (x64)\Video | DecompressorQueue.ByTime | >=0 | 1500 | from 4.10.5.4075 | The key should be used to eliminate frame skip. Sets the time period in milliseconds for the display buffer. The key is applied to the compressed video. Set DecompressorQueue.ByTime=0 to specify buffer size in frames with the DecompressorQueue key |
| x32: (x32)\Video x64: (x64)\Video | StopAllButCurrent | >=0 | 0 | from 4.10.5 | The key adjusts the automatic switching of video streams when changing the number of Video Surveillance Windows in the Video Surveillance Monitor: 0 – if you change the number of video surveillance windows in the Video Surveillance Monitor using the control panel or hot keys, the stream for non-displayed cameras is no longer requested from the server, but the streams are not turned off while a gradual overlap (enlarging by double-clicking) 1 or more – unused streams are disabled both with a gradual overlapping of the Video Surveillance Windows, and with a change in the number of Video Surveillance Windows in the Video Surveillance Monitor using the control panel or hot keys |
| x32: (x32)\Video x64: (x64)\Video | TT_INITIAL | >0 | 1000 | from 4.10.5 | Sets the time period in milliseconds that must elapse after the mouse cursor hovers over a control in the Video Surveillance Monitor for a tooltip to appear |
| x32: (x32)\Video x64: (x64)\Video | TT_AUTOPOP | >0 | 5000 | from 4.10.5 | Specifies the time period in milliseconds during which a tooltip is displayed in the Video Surveillance Monitor |
| x32: (x32)\Video x64: (x64)\Video | hardcoded_hyperlink | URL address | - | from 4.10.5 | Sets the constant part of the link in the device Web interface home page address. If the key is set, the address of the Web interface looks like: hardcoded_hyperlink/<cam_id>. For example, the key is "http://locallhost/". When you go to the IP device’s Web interface from the settings panel of the Camera 1 object, the browser will open the address http://locallhost/1 |
| x32: (x32)\Video x64: (x64)\Video | syncing_cams_max_number | >0 | 10 | from 4.10.5 | The key is in use with the importing from edge storages function. It determines the maximum number of cameras, the archive of which is synchronized after reconnecting to the Server. Reduce the key value if after reconnection with the Server there are gaps in the archive due to HD write queues. |
| x32: (x32)\Video x64: (x64)\Video | BookmarkProtectArchive | 0, 1 | - | from 4.11.0 | If this key is created, then enabling or disabling archive protection when creating a bookmark is not available. 0 – archive protection is disabled when creating a bookmark, this cannot be changed when creating a bookmark 1 – archive protection is enabled when creating a bookmark, this cannot be changed when creating a bookmark |
| x32: (x32)\Video x64: (x64)\Video | IpStorageSyncDepthHours | >0 | 24 | from 4.10.5 | Specifies the time, in hours, for which the archive is to be imported from edge storage. For example, if the last synchronization was performed 34 hours ago, and the key is set to the default value of 24, then after restoring the camera’s connection with the server, the archive will synchronize for only 24 hours. Note. The last synchronization time is set by the SyncedTime parameter in the Settings.xml file |
| x32: (x32)\Video x64: (x64)\Video | MonitorSynchronizedFrameBuffer | >=0 | - | from 4.10.5 | Sets the number of decompressed frames in the buffer during synchronous archive playback. The key must be used if live video fps decreases during synchronous archive playback. 0 – buffering of decompressed frames during synchronous archive playback is disabled > 0 – buffering of decompressed frames during synchronous archive playback is enabled The key is applied to decompressed video. The key is mutually exclusive with MonitorFrameBuffer, i.e. only one of them can be in use at a time |
| x32: (x32)\Video x64: (x64)\Video | Video.ThreadAffinity.Main.CoreCPU | >=0 | 0 | from 4.10.5 | Sets the number of the CPU core, for which the main thread of the Intellect software application is assigned. 0 – the core is not assigned to a thread; it can be used by other threads >= 0 – the core is assigned to the thread and excluded from use by other threads |
| x32: (x32)\Video x64: (x64)\Video | MonitorUpdateInterval | >0 | - | from 4.10.5 | The key sets the update interval for the video image on the Video surveillance monitor. The key value should be increased with increasing load on the system and lowering FPS |
| x32: (x32)\Video x64: (x64)\Video | Monitor_<id>_GreenStreamFactor, where id is an identification number of the Monitor object | <camera_id>:<percentage>, several values can be set separated by comma | * | from 4.11.0 | The key sets the width tolerance of the Video Surveillance window when automatically selecting a stream for display (Green Stream). The percentage in the key value is the fraction of the stream resolution, within which the width of the Video Surveillance window of the camera must be so that this stream is selected (if there are alternatives). The key is set on the Clients and affects only the local Monitor. Examples of values: * – tolerance of 5% (default). Key operation example. |
| x32: (x32)\Video x64: (x64)\Video | ResetFastPlaySpeedOnPause | 0, 1 | 0 | from 4.11.0 | The key enables resetting of the acceleration factor when pausing archive playback in the Video Surveillance Monitor. Note. It is not recommended to set the key to 1 if synchronous archive playback on several cameras is in use |
| x32: (x32)\Video x64: (x64)\Video | BlockGetPositionParams | 0, 1 | 0 | from 4.11.0 | The key disables obtaining absolute coordinates from the camera driver. 0 – Intellect periodically polls the PTZ camera for the absolute coordinates to display the viewing angle on the map 1 – absolute coordinates are not requested, the camera viewing angle on the Map does not change See also Configuring the camera viewing angle display on the Map |
| x32: (x32)\Video x64: (x64)\Video | GreenStreamScaleRatio | >0 | 1 | from 4.11.1 | The key sets the coefficient for calculating the stream resolution when automatically selecting a stream for displaying if it is necessary to select a stream of higher (key value <1) or lower (key value >1) quality than required by default for the corresponding size of the Video surveillance window. The key should be created on the computer where the Video Surveillance Monitor is displayed. For example, to make a stream with a resolution of 640x480 to be selected for a Video surveillance window with a size of 1280x960 pixels, set the key to 2. At the default value, this stream resolution will be too low for the specified size of the Video surveillance window, so another stream will be selected |
| x32: (x32)\Video\Monitor\ DisableStreams\cam<camera_id>\ stream<camera_id.stream_id> x64: (x64)\Video\Monitor\ DisableStreamscam<camera_id>\ stream<camera_id.stream_id> | block_stream | 0, 1 | 0 | from 4.11.2 | The key forbids auto selection of the corresponding stream for displaying. 1 – stream cannot be selected 0 – stream can be selected Example full path to the key: Computer\ HKEY_LOCAL_MACHINE\ SOFTWARE\ WOW6432Node\ ITV\ INTELLECT\ Video\ Monitor \DisableStreams \cam8 \stream8.3 When the key in this path is set to 1, the stream No. 3 on camera 8 will not be selected for displaying |
| x32: (x32)\Video x64: (x64)\Video | LayoutGradualIncrease | 0, 1 | 0 | 4.11.2 | The key enables a gradual increase of the Video Surveillance window on the custom layout by double-clicking the left mouse button. All Video surveillance windows on the layout should be the same size to ensure proper operation of the key. 0 – the Video surveillance window is expanded to the entire Video surveillance monitor by double-clicking the left mouse button 1 – by double-clicking the left mouse button, the Video Surveillance Window is enlarged gradually: the first double-click enlarges it 2 times of the initial size, the second double click enlarges 3 times of the initial size, etc. The Video Surveillance Windows adjacent to it are hidden on the layout |
| x32: (x32)\Video x64: (x64)\Video | UseDefaultLayoutOnlyAtStartup | 0, 1 | 1 | 4.11.2 | Sets the rules for displaying the default layout assigned in the Display Manager (see Selecting the default layout): 1 – the default layout is activated only when Intellect is launched while the last selected layout is displayed whan hiding/displaying/switching displays 0 – the default layout is activated when Intellect is launched, as well as when hiding/displaying/switching displays |
| x32: (x32)\Video x64: (x64)\Video | StopLiveStreamInArchive | 0, 1 | 0 | 4.11.2 | The key disables receiving live video when entering the camera archive in both Video Surveillance Monitor and Cammonitor.ocx ActiveX control. 0 – when entering the archive, live video continues to arrive 1 – live video stops when entering the archive and resumes after quitting the archive mode |
| x32: (x32)\Video x64: (x64)\Video | Threads.AffinityStrategy | 0, 1, -1 | 0 | 4.11.2 | The key sets the threads affinity mode. 0 – if the system has several physical processors, the threads will be bound to one of the processors, but without specifying a specific kernel. Within a single processor, the system will distribute threads across the kernels automatically 1 – threads are bound to a specific kernel of a specific processor -1 – thread affinity is disabled |
x32: (x32)\Video\Monitor\<Monitor number>\Zoom\cam<Camera number> Note. For example, Monitor 1 and Camera 2 will have the following section: \Video\Monitor\1\Zoom\cam2 | blocking | 1 | - | 4.11.2 | The key blocks the ability to scale the video image and move the zoom zone in the viewing tile for the selected Monitor and Camera. The zoom ratio and the zoom zone will be saved in the position which was set before this key was applied. Note. To use this key, it is necessary to restart Intellect |
| x32: (x32)\Video\AVI x64: (x64)\Video\AVI | UseFfmpegConcat | 1 | - | 4.11.2 | The key activates the splicing of video fragments into one file when exporting the archive using the AviExport utility, if the selected export period contains a record from several streams with different video resolutions. In this case, during splicing, the video fragments of lower resolution will be stretched to the highest resolution of the video fragment contained in the exported period of the archive. The resulting file will be in MKV format regardless of the selected container type. Note. The splicing of video fragments of different resolutions without recompression (in the original format) is performed only if all other characteristics of the video, except for the resolution, coincide. If the streams use different codecs, then it is necessary to use recompression to splice the video fragments |
| x32: (x32)\Video x64: (x64)\Video | MonitorExtraTextColor | - | - | 4.11.2 | Sets the unchanging color of the Camera additional information in the Surveillance monitor. The color is set as a decimal number, which is obtained when converting a color represented in HEX according to BGR, where two bytes are allocated for one color. Note. For example, blue in BGR HEX is FF0000. When converting FF0000 to decimal, the number 16711680 is obtained, which should be specified as the key value |
| x32: (x32)\Video x64: (x64)\Video | HideArchControls | 0, 1 | 0 | 4.11.2 | The key hides the archive navigation controls (archive entry button, timeline, playback control bar and videorecords list) in the Cammonitor.ocx ActiveX control 0 – archive navigation items are displayed 1 – archive navigation elements are not displayed |
| x32: (x32)\Video x64: (x64)\Video | DisableAntiAliasingForArchiveVideo | 0, 1 | 0 | 4.11.2 | The key provides the ability to disable smoothing when viewing the archive (see also Setting the parameters of the Monitor interface box). 0 – if the Smoothing checkbox is selected, then smoothing is applied when viewing the archive 1 – regardless of the value of the Smoothing checkbox, smoothing is not applied when viewing the archive |
| x32: (x32)\Video x64: (x64)\Video | AddAllGrabberChannels | 0, 1 | 0 | 4.8.3 | The key allows you to select any PCI channel for the video capture devices, regardless of which channels are already in use by other devices. 0 – you cannot select the same PCI channels for video capture devices of the same type created under the same computer 1 – any PCI channels can be selected for any video input devices |
| x32: (x32)\Video x64: (x64)\Video | Monitor.Native | 0, 1 | 1 | 4.11.2 | The key affects the recompression of live and archived video when playing in the Video Surveillance Monitor: 0 – recompression when displaying video is performed as described in Video signal compression and decompression 1 – recompression is not performed during video playback, i.e. the video is transferred to the Monitor in the format in which it is received by the server or recorded in the archive. Compression and decompression settings on the camera and in the monitor are ignored Note. The key is used for debugging. It is not recommended to change the value of this key |
| x32: (x32)\Video x64: (x64)\Video | ReverseRecompress | 0, 1 | 0 | 4.10.0 | The key enables recompression to MJPEG when playing the archive backward in the Video Surveillance Monitor: 0 – when playing backward, video is decompressed and uncompressed video is buffered 1 – when playing backward, video is recompressed to MJPEG format |
| x32: (X32)\Video\Monitor\<monitor number>\DisableMouse x64: (x64)\Video\Monitor\<monitor number>\DisableMouse | WM_LBUTTONDBLCLK | 1 | - | 4.11.2 | If the key is specified, then the selected Monitor will ignore a left double-click. Note. The key is used to prohibit unfolding the camera on the Video Surveillance Monitor using the mouse |
| x32: (X32)\Video\Monitor\<monitor number>\DisableMouse x64: (x64)\Video\Monitor\<monitor number>\DisableMouse | WM_RBUTTONDBLCLK | 1 | - | 4.11.2 | If the key is specified, then the selected Monitor will ignore a right double-click. Note. The key is used to prohibit unfolding the camera on the Video Surveillance Monitor using the mouse |
| x32: (X32)\Video\Monitor\<monitor number>\HardLayout x64: (x64)\Video\Monitor\<monitor number>\HardLayout | <Number of camera windows> | <Number of fold columns>, <Number of fold rows>. The values should be >0. For example, 3,2—sets the fold display of the size 3x2 | - | 4.11.2 | The key specifies the fold on the selected Monitor to display a certain number of camera windows. In the <Number of camera windows> parameter, you must specify the number of cameras added to Intellect that will be displayed in the Monitor. The key will be ignored if the specified number doesn’t match the number of cameras actually added. Example of the full path to the key and the parameter: Computer\HKEY_LOCAL_MACHINE\SOFTWARE After creating this parameter to display three camera windows, a fold of 4x5 will be displayed on the Monitor 2. Note. If the Control panel is enabled in the Monitor (see Setting the parameters of the Monitor interface box), the fold specified by the key is ignored and is switched to the default fold (see Changing the number of Surveillance windows) Note. Restart Intellect to use the key |
| x32: (x32)\Video x64: (x64)\Video | SendFrameArchExactDelay | >=0 | 1000 | 4.11.2 | The key sets the video display delay in milliseconds when navigating the upper timeline of video viewing in the archive |
| x32: (x32)\Video x64: (x64)\Video | Monitor.ShowTimeMS | 0, 1 | 0 | 4.11.2 | If the key is specified, then the video recording time in milliseconds will be displayed in the lower right corner of the video playback window. 0 – time is not displayed 1 – time is displayed |
| x32: (x32)\Video x64: (x64)\Video | TrySquareLayout | 0, 1 | - | from 4.11.3 | If the key is specified, then symmetrical folds are used for displaying camera windows in the MonitorThe key enables the usage of symmetrical folds to display the camera windows in the Monitor in the Alarm cameras mode. The key applies only when the Keep camera ratio checkbox is set (see Setting the parameters of the Monitor interface box). 1—symmetrical folds of the Monitor are used, sufficient to display the required number of cameras: 1, 2x2, 3x3, 4x4, etc.0—folds are not used for display 0—camera windows will fill the entire space of the Monitor window |
| x32: (x32)\Video x64: (x64)\Video | HideInMenuVideoServer | 0, 1 | 0 | from 4.11.3 | When you switch to the archive in the Monitor, this key disables the ability to select a Video Server as a source. 0 − Video server can be selected 1 − Video server selection button is hidden |
| x32: (x32)\Video x64: (x64)\Video | CanUseVmdaFilters | 0, 1 | 1 | from 4.11.3 | The key hides the Save the template and Load the template menu items of the Archive search item in the Monitor. 1 − menu items are available 0 − menu items are hidden |
| x32: (x32)\Video x64: (x64)\Video | HideArchSaveAndPrintButtons | 0, 1 | 0 | from 4.11.3 | The key hides the buttons for print, export and scale in the Monitor in archive view mode. 1 − buttons are hidden 0 − buttons are available |
| x32: (x32)\Video x64: (x64)\Video | Monitor.IgnoreFastClientSkip | 0, 1 | 0 | from 4.11.2 | The key enables decimation on the Client (Remote Client) when playing back the video archive at an increased speed. The key is created on the Client. 1 - decimation on the Client is disabled 0 - decimation on the Client is enabled |
| x32: (x32)\Video x64: (x64)\Video | GateDisableHotStartVideo | 0, 1 | 1 | from 4.11.3 | The key disables the start of retransmission and video recording through the Videogate. The key directly affects the work of the START_VIDEO and STOP_VIDEO commands for GATE Videogate. 1—the START_VIDEO and STOP_VIDEO commands don’t work, i.e. video isn’t retransmitted and isn’t written to the archive 0—the START_VIDEO and STOP_VIDEO commands work, video is started and written to the archive |
| x32: (x32)\Video x64: (x64)\Video | StatusInfo | 0, 1 | - | from 4.11.3 | Enables logging detailed information about the file system and memory usage for each camera to the video.run log file when the debugging mode is enabled (Debug=4). 0—basic information about the file system is displayed (6 lines, updated every 10 seconds) 1—detailed information about the file system is displayed (maximum amount of data available, updated every 10 seconds) By default, the key is not created, the system behavior with Debug=4 corresponds to StatusInfo=1 |
| x32: (x32)\Video x64: (x64)\Video | ShowFrameSkippedStatus | 0, 1 | 1 | from 4.11.3 | Enables the indication of no archive recording by camera in the Video surveillance monitor if there are frames skipped during archive recording (i.e., the FRAME_SKIPPED events are received, see Indication of camera status). 1—if there are frames skipped, the disk absence icon will be displayed below the corresponding camera number 0— the icon won’t be displayed if there are frames skipped |
| x32: (x32)\Video x64: (x64)\Video | EmbededDetectorsLifetime | >0 | - | from 4.11.3 | Sets in milliseconds the duration of displaying the trigger frame of the Embedded detection in the Video surveillance monitor (see Embedded detectors). By default, the key is not created. |
| x32: (x32)\Video x64: (x64)\Video | UseObsoleteAttribute | 0, 1 | - | from 4.11 | Disables the display of found obsolete devices (deprecated in Drivers Pack) when searching using the Camera discovery tool. 1—deprecated devices are not displayed in search results. 0—deprecated devices are displayed in search results. By default, the key is not created |
| x32: (x32)\Video x64: (x64)\Video | MonitorToTelemetryDirectCommand | 0, 1 | 0 | from 4.9.8 | The key specifies the way of transmission telemetry commands when controlled from the Video surveillance monitor: 1—when you control telemetry from the Video surveillance monitor, the telemetry server connects directly to the video servers and sends commands to the devices. 0—when you control telemetry from the Video surveillance monitor, the telemetry server sends commands to the Intellect core, which sends them to devices. The key is used together with the TelemetryDirectCommand key (see below in the Telemetry section) to provide smoother telemetry control. Recommended values of these keys: TelemetryDirectCommand = 1 (default value) MonitorToTelemetryDirectCommand = 1 (attention: default value is 0) Attention! When you use these registry keys, Client, server and camera must be in one subnet without Videogate. Otherwise, the system won’t operate |
...
Overview
Content Tools