Go to documentation repository
Page History
The settings panel of the RTSP Server object is shown in the figure.
The Basic settings tab.
The Advanced settings tab
Table describes the parameters of the settings corresponding to the elements of the settings panel of the RTSP Server Tables describe the setting parameters of the RTSP Server system object.
№ | Parameter | Method for setting the parameter value | Parameter description |
Representation | Default value | Value range |
1 |
Identification number* | Automatically | Displays the |
identification number of the RTSP Server object in the digital video surveillance system |
Numbers, letters, periods, hyphen, dash and underscore | - | Depends on the number of the RTSP Server objects in the digital video surveillance system |
2 | Name* |
Enter the value |
into the field | Sets the name of the RTSP Server object in the digital video surveillance system | Latin, Cyrillic and service characters | RTSP Server | A line containing a sequence of any |
characters (letters, digits, service characters |
except > and < |
characters), |
case- |
insensitive. Number of |
characters—from 1 to 60 |
3 | Disable |
Set the checkbox | Sets the state (enabled or disabled) of the RTSP Server object in the digital video surveillance system | Boolean type |
Clear |
Set—the RTSP Server object is disabled and |
isn't used Clear—the RTSP Server object is enabled and |
used | |
4 | Computer |
Select the value from the list | Sets the |
Computer parent object to which the given RTSP Server object |
belongs | Names of the Computer objects registered in the system | Name of the Computer parent |
object | Depends on the number of Servers in the digital video surveillance system with the distributed architecture |
The Basic settings tab | ||||||
5 | Cameras |
Set the checkbox | Specifies the cameras the video signals from which |
should be transmitted to remote workstations | Boolean type |
Clear |
Set—the video stream can be viewed at a remote workstation |
Clear—the video stream cannot be viewed at a remote workstation |
6 |
Gate | Select the value from the list | Specifies the Videogate through which video is received from the camera | Names of the Videogate objects registered in the system | - | Depends on the number of the Videogate objects registered in the system | |
7 | Port | Enter the value into |
the field | Sets |
the port via which a video signal from the camera |
will be transmitted. Note. This column is available only if is the Multicast |
checkbox is set |
( |
12). |
Specified ports are not addressed directly. Use the RTSP port to get video from all cameras in the Multicast mode ( |
14) |
Sequence of numbers | - | Any |
available unused port numbers. The number of ports is specified by the |
system administrator |
8 |
Backup arch. | Select the value |
from the list | Specifies the |
Backup archive from which the archive is received |
for the camera |
Names of the |
Backup archive objects registered in the system | - | Depends on the number of |
the Backup archive objects registered in the system |
9 | Unicast |
Set the checkbox | Enables the "unicast" transmitting mode | Boolean type |
Set |
Set—the video is transmitted in the "unicast" mode |
Clear—the video |
isn't transmitted in the "unicast" mode |
10 | RTSP port |
Enter the value |
into the field | Sets the port via which the video |
signal will be transmitted | Sequence of numbers | 554 | Any |
available unused port numbers. The number of ports is specified by the |
system administrator |
11 | HTTP port |
Enter the value |
into the field | Sets the port which |
should be |
used for transmitting the video signal via the http |
protocol | Sequence of numbers | 8081 | Any |
available unused port numbers. The number of ports is specified by the |
system administrator |
12 | Multicast |
Set the checkbox | Enables the video transmission via different RTSP ports. The Multicast mode allows reducing the Server load |
by reducing the amount of the transmitted data |
Boolean type |
Clear |
Set—the video is transmitted in the "multicast" mode |
Clear—the video |
isn't transmitted in the "multicast" mode |
13 | Receiver IP address |
Enter the value |
into the field |
Sets the IP address from which the |
video will be transmitted in the Multicast mode |
IP address | 224.0.1.150 | From 224.0.0.0 to 239.255.255.255 |
14 | RTSP port |
Enter the value |
into the field | Sets the port number |
via which the video signal will be transmitted in |
the Multicast |
mode. When requesting the video data from the camera using the RTSP protocol, it is necessary to specify this port. The system |
forwards the request to the port of the requested camera |
Sequence of numbers | 555 | Any |
available unused port numbers. The number of ports is specified by the |
system administrator |
The Advanced settings tab.
№ | Parameter | Method for setting the parameter value | Parameter description | Representation | Default value | Value range |
1 | VLC player compatibility mode |
Set the checkbox | Enables sending the current time to VLC Media Player instead of the frame time |
Boolean type |
Clear |
Set—the current time is sent to VLC Media Player |
Clear—the frame time is sent to VLC Media Player |
2 | Use captions track |
Set the checkbox | Enables sending the video captions along with video |
image via the RTSP Server | Boolean type |
Clear |
Set—if there are captions on the video image, they are sent |
to the the receiving app |
Clear—the video captions are not sent via the RTSP Server |
3 | Source IP interface | Select the value |
from the list | Sets the name of the network interface that should be used to |
transmit the RTSP |
Server | Names of the network interfaces | ANY | The list of the available network interfaces of the computer. ANY |
—the default network interface is used |
The NAT |
settings group |
4 | IP |
address |
Enter the value |
into the field | Sets the IP address of the router that performs the NAT |
transmission | IP address | - | IP addresses range for the local network |
5 | Port |
Enter the value |
into the field | Sets the port of the router that performs the NAT |
transmission | Sequence of numbers | 0 | 0-65535 |
*The name Name of the element is not isn't displayed in the settings panel of the given object.