Page History

1

Identification number

*

Automatically

Displays the identification number of the Operator protocol object in the system

Numbers, letters, periods, hyphen, dash and underscore

-

Depends on the number of the Operator protocol objects in the system

2

Name

*

Enter the value

into the field

Sets the name

of the Operator protocol object

in the system

Latin, Cyrillic and service characters

Operator protocol

A line containing a sequence of any

characters (letters, digits, service

characters

except > and <

characters),

case-

insensitive.

Number of

characters—from 1 to 60

3

Disable

Set the checkbox

Sets the status (enabled or disabled) of the Operator protocol object in the system

Boolean type

Clear

Set—the Operator protocol object is disabled and

isn't used

Clear—

the Operator protocol object is enabled and

used

4

Display

Select the value from

the list

Sets the Display parent

object

for the given Operator protocol object

Name of the Display

objects registered in the system.

Name of the Display parent

object

Depends on the number of the Display

objects in the system

5

X

Enter the value

into the field

Sets the X coordinate in the

horizontal axis for the upper left corner of the Operator protocol interface

window

% of the screen width

-

From 0 to M*100, where M

is the number of the installed monitors

Y

Enter the value

into the field

Sets the Y coordinate in the

vertical axis for the upper left corner of the Operator protocol interface

window

% of the screen height

-

From 0 to M*100, where M is the number of the installed monitors

6

W

Enter the value

into the field

Sets the

width of the Operator protocol interface

window

% of the screen width

-

From 0 to M*100, where M is the number of the installed monitors

H

Enter the value

into the field

Sets the

height of the Operator protocol interface

window

% of the screen height

-

From 0 to M*100, where M is the number of the installed monitors

7

Allow moving

Set the checkbox

Allows

moving the Operator protocol interface

window manually

Boolean type

Clear

Set—allow moving the Operator protocol interface window manually

Clear—disable moving the Operator protocol interface window manually

Opens a test window to set the position of the Operator protocol interface window

11

Type

Select the value from

the list

Sets the type of objects

, the events from which should be displayed in the Operator protocol

window

Available object types

-

Depends on the objects registered

in the system.

Only the objects for which the INFORMATION or ALARM value is selected in the Messages processing column on the Events tab in the ddi.exe utility are available for selection (see The Events tab

)

12

Number

Select

the value from the list

Sets the number of an object

, which

events

should be displayed in the Operator protocol

window

Sequence of numbers

-

Depends on the number of

the objects of the specified type registered in the system

13

Name

Automatically

Sets the name of an object

, which

events

should be displayed in the Operator protocol

window

Names of the objects registered

in the system

-

Depends on the objects registered

in the system

14

Event type

Select

the value from the list

Sets the events displayed in the Operator protocol interface

window

Events available for the selected object

-

Depends on the object type

15

Request password

Select

the value from the list

Defines the necessity of password to process the event

Boolean type

-

Set—password confirmation is required to process the event

Clear—password confirmation isn't required to process the event

16

Region

Select

the value from the list

Sets the Region object corresponding to the monitored object

List of

the Region objects created in the system

-

Depends on the number of

the Region objects created in the system

17

Parameter

Enter the value into the field

Sets the parameter of the monitored object

Depends on the event type

-

Depends on the event type

1–10

The lower the value, the higher the priority

Sets the name of the parameter, the value of which

should be displayed in the Operator protocol interface

window

22

Description

Enter the value

into the field

Enter a short description of the specified parameter

Latin, Cyrillic and service characters

-

0–255 characters

Sets the Operator protocol object, to which the events

should be sent after the time specified in the Wait for

operator response for field

Depends on the number of

the Map objects created in the system

ActiveX—archive will open in a separate window

Monitor—archive will open on the selected Video surveillance monitor

Sets the time after which the event

will be assigned the Non-processed event type or the event

will be escalated

0–10000

Fractional values can be specified; integer and fractional parts are point-separated.

For

example, to set 2 minutes 30 seconds time period

, enter 2.5

Enter the maximum number of events that can be displayed simultaneously in the list of the current events

0–600

The value is not specified or

0—the operator can not

delay the event processing

Greater than

0—the parameter sets the time for which the operator can

delay the event processing

Fractional values can be specified; integer and fractional

parts are point-separated. For example, to set

2 minutes

30 seconds time period, enter 2.5

Enables the sorting of events by priority. The descending sorting is performed in this order: Escalated, Alarm, Information and Standard (the last three event parameters can be set in the DDI file—see The Events tab)

Set—sorting by priority is enabled

Clear—sorting by time the events are received is enabled

Places

new events at the end of the current events list

Set—

new event is placed

at the end of the list

Clear—new event is

placed at the beginning of the list

Set—when the event is processed in one of the Operator protocol, it is deleted from other Operator protocols

Clear—when the event is processed in one of the Operator protocol, it stays unprocessed in other Operator protocols

Sets the necessity to enter the password to process the event 

Set—the event processing

must be confirmed with a password

Clear—password is not required for event processing

34

Autoswitch

Set the checkbox

Enables autoswitch to the Current events tab in the Operator protocol window when a new event occurs

Boolean type

Clear

Set—autoswitch is enabled

Clear—auto switch is disabled

Set—the cell of the event received last is automatically activated

Clear—when the new event is received, the cell selected by the Operator remains active

Set—the event processing buttons are displayed when a group of events is selected

Clear—the event processing buttons are hidden when a group of events is selected

Set—the comment field is automatically cleared after the event has been processed by the Operator

Clear—the comment text remains in the comment field after the event has been processed by the Operator

Set—the cell size is set equal to the size of the Operator protocol window area, that is not occupied by the event control panel

Clear—the cell size is set according to the content size

Set—the Apply to all button is hidden in the Operator protocol window, and the Operator cannot process all events at once

Clear—the Apply to all button is available in the Operator protocol window

Set—the Operator protocol window is displayed on top of all windows

Clear—the Operator protocol window is displayed in the standard mode

Set—the buttons for classifying the events (Alarm situation, Suspicious situation, False alarm) do not appear until the Comment field is filled

Clear—the Operator can classify (process) the event without entering a comment

Prevents the Operator from selecting multiple events using the Shift and Ctrl keys

Set—the Operator cannot select multiple events using the Shift and Ctrl keys

Clear—the Operator can select multiple events using the Shift and Ctrl keys