Page History

Configuring the parameters

...

To configure the Close-standing people

...

detector, do the following:

1. Create

...

1. the Human pose detector (see Configuring the Human pose detector).
2. Below the

...

1. Human pose detector, click Create… → Close-standing people

...

1. detector.

By default, the Close-standing people detection triggers detector generates an event when "skeleton" bounding boxes around people collide. 

Info
title Note
Bounding boxes are not displayed in the interface. They are usually a bit larger than the "skeletons" dimensions.

If necessary, you can change the detection tool detector parameters. The list of parameters is given in the table:

Parameter	Value	Description
Other
Enable	Yes	The

detection tool

detector is enabled by default. To disable the

detection tool

detector, select

the 

the No

 value

value
	No
Name	Close-standing people

detection

detector

Enter the

detection tool

detector name or leave the default name
Type	Close-standing people

detection

detector

Name of the

detection tool

detector type (non-editable field)
Basic settings
Distance sensitivity	2	Specify the distance between people in meters at which the

detection tool must trigger. Alarm will be

detector must generate an event. An event is generated if the distance between people in the frame is equal to or less than the specified distance. The value must be in the range [0, 20]
Leveling rod length	1.7	Specify the average height of a person in meters, according to which the leveling rods are set. The value must be in the range [0 3]
Number of measurements in a row to trigger detection	4	Specify the minimum number of frames with close-standing people for the

detection tool to trigger. 

detector to generate an event. The value must be in the range [1, 100]. Increasing the value can help eliminate false

alarms

event, but increases the risk of skips.  Decreasing the value can help reduce skips,

but increases

but increases the probability of false

alarms

events

To save the parameters of the detection tooldetector, click the Apply Apply Image Modified button. To cancel the changes, click the Cancel Cancel Image Modified button button.

Configuring the frame perspective 

if If you want to change the triggering distance that must generate an event, you must configure the frame perspective:

1. In the preview window, click
the 
2. the Image Modified
 button
3.  button.
4. Specify the size of the same object in different parts of the frame by eye
.
5. :
   • To create a leveling rod, left-click the video image to add two anchor points.
You must set
6. • Set at least

three leveling rods. 

7. • three calibration rods. The lower anchor points of any three rods must not be located on the same line (horizontal, vertical, slanting, and so on).

   • The size of the leveling rod must be about the average height of a person at this part of the frame.
   • You can resize the rod by stretching its anchor
points 
8. • points Image Modified. You can move it on screen
by 
9. • by dragging and dropping.
     Image Modified
     

     Note
     title Attention!
     When you set up leveling rods, the following conditions must be met: the rods that are located at the same distance from the camera lens

,

10. • must be of the same size; the feet of the rods must be located on the same surface (for example, floor); in complex scenes, we recommend adding more than three rods to increase the accuracy of the detection; in the parts of the frame where the lens vertical distortion is observed, the rods must be parallel to the nearest vertical objects (for example, door

,

11. • or wardrobe); for portrait-oriented scenes (such as corridor, shopping aisle, warehouse aisle, and so on), the arrangement of the rods must form triangles.

      Info
      title Note
      For convenience of configuration, you can "freeze" the frame. Click

the 

12. • the Image Modified

 button

13. • button. To cancel the action, click this button again. The area for detection is displayed by default. To hide it, click

the 

14. • the Image Modified

 button

15. • button. To cancel the action, click this button again. To delete a rod, click

the 

16. • the Image Modified

 button

17. • button.

      
      
18. Click
the Apply button
19. the Apply button.

Configuration of the Close-standing people detector is complete.