Page History

To add Suprema fingerprints in the Access Manager module, do the following:

1. Go to adding biometric data in the Access Manager window (see Adding biometric parameters).
2. Select the (Edit Fingerprints) Suprema Host Controller or Suprema Slave Controller extension that corresponds to the controller with the biometric fingerprint reader connected to it.
3. The Suprema. Edit fingerprints dialog box will open. To add a new fingerprint, click the Add button.
   Image Added
   The Suprema. Capture fingerprints window will open.
   Image Added
4. From the Mode drop-down list (1) select the fingerprint capture mode:
   • One finger - reading a single fingerprint.
   • Two fingers - reading two fingerprints.
   • Two thumb fingers - reading two thumb fingerprints.
   • Left four fingers - reading fingerprints of four fingers of the left hand.
   • Right four fingers - reading fingerprints of four fingers of the right hand.
   • Ten fingers - reading 10 fingerprints.
   • Left palm - reading the left palm print.
   • Right palm - reading the right palm print.
   • One roll finger - reading a single fingerprint with an offset.
5. From the Quality drop-down list (2) select the fingerprint capture quality:
   
   • 20 (Weak) - low quality.
   • 40 (Moderate) - average quality (default).
   • 60 (Strong) - high quality.
   • 80 (Strongest) - the highest quality.

6. To start capturing fingerprints, click the Start capturing button (3) and follow the instructions displayed at the top of the Suprema. Capture fingerprints window.

   Info
   title Note
   To capture fingerprints, each finger or group of fingers should be placed on the reader twice with 5 seconds delay after pressing the Start capturing button and after the first capture.

   
   

7. After the fingerprint capture is completed, select the type of scanned finger for each fingerprint in the drop-down list (1):

   • Undefined - undefined.
   • Left thumb - thumb of the left hand.
   • Left index finger - index finger of the left hand.
   • Left middle finger - middle finger of the left hand.
   • Left ring finger - ring finger of the left hand.
   • Left little finger - little finger of the left hand.
   • Right thumb - thumb of the right hand.
   • Right index finger - index finger of the right hand.
   • Right middle finger - middle finger of the right hand.
   • Right ring finger - ring finger of the right hand.
   • Right little finger - little finger of the right hand.

   Image Added

8. Uncheck the Add check box (2) if it is not necessary to add the fingerprint to the user.

9. Click OK to save the result.

10. The captured fingerprints will be displayed in the Suprema. Edit fingerprints window.
    Image Added

11. To remove one fingerprint, select it and click Remove.

    Info
    title Note
    To remove all fingerprints, click Remove all.

    
    

12. To mark a fingerprint as captured "Under duress", select it and click the [Duress] button.

    Info
    title Note
    As a result, a silent alarm will be generated when reading this fingerprint.

    
    

13. To move a fingerprint up or down in the list, select it and click the Up or Down button.

14. To finish entering fingerprints, click OK.

The Suprema fingerprints are added

Capturing fingerprints in Access Manager with Suprema readers is carried out as follows:

1. Open the Access Manager window (see Starting and stopping the Access Manager module).
2. Go to user editing (see Going to user editing).
3. Right-click the user's photo in the Access Manager window and select Extensions.
   Image Removed
4. Select Suprema Host Controller or Suprema Slave Controller to use the reader connected to the corresponding controller (for information on configuring the readers see Configure the interaction between the Suprema Biometrical ACS and the Access Manager module).
   In both cases, the Suprema dialog will open.
   Image Removed

5. The existing fingerprints are displayed in the (1) list. The first two fingerprints highlighted in bold will be written to the Suprema controller. To delete a fingerprint, select it in the list and click Remove (2). To delete all user fingerprints, click Remove all (3).

6. Click Add (4) to start capture. The capture dialog will open.

   Image Removed

7. Click Start Capturing (1).

8. Put finger on reader and wait until two copies of a fingerprint are captured (1). 
   Image Removed
9. To finish capture, click OK (2).
10. Click Save (1) in the user editor to add the fingerprint to the user account. 
    Image Removed.

Capturing fingerprints in Access Manager with Suprema readers is complete.