Page History

...

To use multistreaming over the ONVIF protocol, select ONVIF 2.X brand and 1-channel-multistream model when creating an ONVIF device (using Camera discovery tool, see Installing and configuring security system components guide). Two streams will be available.

...

To configure multistream settings, do the following:

1. Go the Hardware tab in the System Settings dialog (1)the Hardware tab (1) in the System Settings dialog window.
2. In the object tree on the the Hardware tab tab, select the previously created Camera object created Camera object (2) that corresponds to the video camera for which multistream mode is to be configured (2). The right part of the the Hardware tab  tab shows the settings panel for the selected object.
3. On the the Camera object object's settings panel, go to the the Advanced settings tab  tab (3).
   Image Modified
4. To enable multistream mode, check the the Video stream setting box  box (4). This will display tabs tabs (5) for configuring the camera's video streams (5).

5. By default, all streams are enabled. If it is necessary to disable unused streams, clear the check boxes that correspond to the numbers of the relevant streams (6).

6. Set the the Default switch  switch (7) to the position corresponding to the stream number of stream that is to should be used in use in the following cases:

   1. To display video both locally and on remote clients;

   2. To send to remote clients, including the Videogate, that can record this video stream;

      Info
      title Note.
      If a specific video stream is requested via Video gate, then the requested stream is send to Video gate, not the Default stream.

      
      

   3. When a video stream is not specified for the video request.

   Info
   title Note.
   This stream is used, for example, to display video on the Video Surveillance Monitor if a default stream has been selected for the camera or for displaying video on the Video Surveillance Monitor of the web server.

   
   

7. Set the the Video analytics radio button  switch (8) to the number of position corresponding to the stream to number that should be used by sensors (8). This stream will be used for for the LPR channel, the main motion detection tool, zone detection tools, tracking detection tool and face detection tool (if an external recognizer is not in useused).

   For the license plates recognition server, face detection tool (if an external recognizer is in use) and detection tools that are the part of the Detector Pack subsystem, the "Default" stream is in use.

8. Set the Archive switch Set the Archive switch (9) to position corresponding to the number of stream that is to be recorded to the archive not upon alarm – the continuous recording is performed (9). 

9. Set the Archive(alarm) switch the Archive (alarms) switch (10) to position corresponding to the number of stream that is to be recorded to the archive upon alarm (10).

   This stream is also used for Backup archive.

   Info
   title Note.
   If different streams are selected for recording to the archive upon alarms and continuous recording, recording is performed non-stop and detection tools are enabled, then upon alarm recording of the current archive fragment is stopped in the continuous recording stream and recording of a new fragment starts in the alarm recording stream. When the alarm ends and after pre-alarm recording the continuous recording with the corresponding stream resumes. If the same stream is selected for recording to the archive upon alarms and continuous recording, then recording of current fragment is not stopped upon alarm.

   
   

   Info
   title Note.
   If pre-alarm recording is configured, then when different streams are selected for recording to the archive and continuous recording, some archive recordings overlay as the following video fragment starts before the previous ends.

   
   

10. Configure the video streams as follows:
    
    1. Go to the tab that corresponds to the desired video stream (11).
       
    2. The Purpose field field (12) displays a description of how the video stream is used (12).

    3. Specify the video stream's parameters (13) (see The Settings panel of the Camera object).

       Note
       title Attention!
       Following video streams are available for Axis cameras: 1. Receiving of H264/MJPEG/MPEG4 video. It is available to specify settings of video stream using the Intellect software package facilities. Settings are specified in the Video stream 1 tab. 2-4. Stream corresponding to “Quality”, “Balanced” and “”Bandwidth” profiles. These profiles configure in the camera web-interface. Video stream 2 corresponds to the “Quality” video stream, Video stream 3 corresponds to the “Balanced” video stream, Video stream 4 corresponds to the “Bandwidth” video stream.

       
       

    4. Repeat steps a-d for the remaining video streams.
11. Click the Apply button.

...