The Settings panel of the RTSP Server object

The settings panel of the RTSP Server object is shown in the figure.

The Basic settings tab.

Tables describe the setting parameters of the RTSP Server system object.

№	Parameter	Method for setting the parameter value	Parameter description	Representation	Default value	Value range
1	Identification number*	Automatically	Displays the identification number of the RTSP Server object in the digital video surveillance system	Numbers, letters, periods, hyphen, dash and underscore	-	Depends on the number of the RTSP Server objects in the digital video surveillance system
2	Name*	Enter the value into the field	Sets the name of the RTSP Server object in the digital video surveillance system	Latin, Cyrillic and service characters	RTSP Server	A line containing a sequence of any characters (letters, digits, service characters except > and < characters), case-insensitive. Number of characters—from 1 to 60
3	Disable	Set the checkbox	Sets the state (enabled or disabled) of the RTSP Server object in the digital video surveillance system	Boolean type	Clear	Set—the RTSP Server object is disabled and isn't used Clear—the RTSP Server object is enabled and used
4	Computer	Select the value from the list	Sets the Computer parent object to which the given RTSP Server object belongs	Names of the Computer objects registered in the system	Name of the Computer parent object	Depends on the number of Servers in the digital video surveillance system with the distributed architecture
The Basic settings tab
5	Cameras	Set the checkbox	Specifies the cameras the video signals from which should be transmitted to remote workstations	Boolean type	Clear	Set—the video stream can be viewed at a remote workstation Clear—the video stream cannot be viewed at a remote workstation
6	Gate	Select the value from the list	Specifies the Videogate through which video is received from the camera	Names of the Videogate objects registered in the system	-	Depends on the number of the Videogate objects registered in the system
7	Port	Enter the value into the field	Sets the port via which a video signal from the camera will be transmitted. Note. This column is available only if is the Multicast* checkbox is set (12).* Specified ports are not addressed directly. Use the RTSP port to get video from all cameras in the Multicast* mode (14)*	Sequence of numbers	-	Any available unused port numbers. The number of ports is specified by the system administrator
8	Backup arch.	Select the value from the list	Specifies the Backup archive from which the archive is received for the camera	Names of the Backup archive objects registered in the system	-	Depends on the number of the Backup archive objects registered in the system
9	Unicast	Set the checkbox	Enables the "unicast" transmitting mode	Boolean type	Set	Set—the video is transmitted in the "unicast" mode Clear—the video isn't transmitted in the "unicast" mode
10	RTSP port	Enter the value into the field	Sets the port via which the video signal will be transmitted	Sequence of numbers	554	Any available unused port numbers. The number of ports is specified by the system administrator
11	HTTP port	Enter the value into the field	Sets the port which should be used for transmitting the video signal via the http protocol	Sequence of numbers	8081	Any available unused port numbers. The number of ports is specified by the system administrator
12	Multicast	Set the checkbox	Enables the video transmission via different RTSP ports. The Multicast mode allows reducing the Server load by reducing the amount of the transmitted data	Boolean type	Clear	Set—the video is transmitted in the "multicast" mode Clear—the video isn't transmitted in the "multicast" mode
13	Receiver IP address	Enter the value into the field	Sets the IP address from which the video will be transmitted in the Multicast mode	IP address	224.0.1.150	From 224.0.0.0 to 239.255.255.255
14	RTSP port	Enter the value into the field	Sets the port number via which the video signal will be transmitted in the Multicast mode. When requesting the video data from the camera using the RTSP protocol, it is necessary to specify this port. The system forwards the request to the port of the requested camera	Sequence of numbers	555	Any available unused port numbers. The number of ports is specified by the system administrator

The Advanced settings tab.

№	Parameter	Method for setting the parameter value	Parameter description	Representation	Default value	Value range
1	VLC player compatibility mode	Set the checkbox	Enables sending the current time to VLC Media Player instead of the frame time	Boolean type	Clear	Set—the current time is sent to VLC Media Player Clear—the frame time is sent to VLC Media Player
2	Use captions track	Set the checkbox	Enables sending the video captions along with video image via the RTSP Server	Boolean type	Clear	Set—if there are captions on the video image, they are sent to the the receiving app Clear—the video captions are not sent via the RTSP Server
3	Source IP interface	Select the value from the list	Sets the name of the network interface that should be used to transmit the RTSP Server	Names of the network interfaces	ANY	The list of the available network interfaces of the computer. ANY—the default network interface is used
The NAT settings group
4	IP address	Enter the value into the field	Sets the IP address of the router that performs the NAT transmission	IP address	-	IP addresses range for the local network
5	Port	Enter the value into the field	Sets the port of the router that performs the NAT transmission	Sequence of numbers	0	0-65535

*Name of the element isn't displayed in the settings panel of the given object.

Page tree

Documentation for Intellect 4.11.0-4.11.3. Documentation for other versions of Intellect is available too.