Documentation for Auto Intellect 5.5. Documentation for other versions of Intellect is available too.

Previous page Operating system requirements  Video camera mounting and setup requirements for the Auto-Uragan software module Next page


On the page:
 

Camera location on the road

By default, the cameras are installed at a height of 6 m above the controlled lane edge. The control zone center is located 20 m from the camera. The camera is tilted at an angle of 18 degrees.
We recommend placing the cameras above the edge of the road, and not above the center. In this case, the horizontal inclination will amount to 4 degrees for the control zone width of 3 m.

Camera location at the security sites

By default, the cameras controlling the security site entrances and exits are located at a height of 3 m above the lane edge. The control zone center is then located 11 m from the camera.

 

Setup of the lens focal length

After the camera is mounted, the lens focal length should be adjusted to the required viewing distance.

To set up the lens without the Uragan software, do the following:

  1. Direct the camera at the road area where the license plate numbers are to be read;
  2. Place a license plate in the center of the control zone. The plate should be perpendicular to the camera axis;
  3. Zoom the lens to make the license plate occupy approximately 1/5 of the image at the center of the image;
  4. Lock the zoom position;
  5. Adjust the image sharpness.

Camera setup

To set up the camera, do the following:

  1. Set the required shutter speed.

    Note.

    1/1000 sec is enough in most cases.

  2. Set maximum sharpness and dynamic range of the signal, if the camera includes the video signal Level adjustment.
    Do the following:
    2.1 Aim the camera at a very bright object to catch as much light as possible (but not at the sun!). Decrease the Level value until the image disappears – the lens closes and the image becomes black.
    2.2 Gradually increase the Level value until the image appears.
    2.3 Close the lens for 5 sec using any opaque object (eg. the palm of your hand). Open the lens again.
    2.4 Make sure the image reappears. If the image does not appear, increase the Level value and check the image again.
  3. Set the image sharpness. The sharpness should be set up under poor lighting conditions (approx. 10 – 100 lux), when the noise level is just below the signal level. To achieve such conditions, the dark lens filter can be used.

General parameters of used video cameras

General parameters of used video cameras are presented in the following table.

№

Property

Range

Comment

1

Camera type

CCTV

Analog and IP-cameras can be in use.

2

Camera resolution

Not less than 520 TVL horizontally.

Only high resolution CCTV camera usage guarantees the recognition rate declared in the technical characteristics of the system.

3

Illuminance of the monitored area

Not less than 50 lux for cameras with 0.05 lux CCD sensitivity;
Not less than 20 lux for cameras with 0.0002 lux CCD sensitivity;
0 lux for cameras with IR illumination.

At night time, standard auto road illumination devices are sufficient to provide 50 lux illuminance in full compliance with the building regulations.

4

Automatic amplification adjustment

LOW or MIDDLE depending on the camera

This function must be enabled. Unfortunately, the scene is usually not sufficiently illuminated, thus the image looks too dark in case this function is disabled. Enabling this function amplifies the whole video signal including the CCD noise. The amplification value is chosen for each camera separately.

5

Auto aperture and auto electronic shutter

  • not more than 1/500 sec for vehicle speed below 40 km/h;
  • not more than 1/1000 sec for fast motions (vehicle speed above 40 km/h).

The image should be sharp. Sharpness can be achieved by locking the shutter speed (exposure). Locking the speed of the electronic shutter is a very important function.
When the exposure is long, i.e. the shutter speed is low (1/100, 1/50 sec), the moving objects are blurred in the image. This most affects the small details, eg. the symbols in license plate numbers. The video sequence as a whole may look good enough, but the static frames that comprise it may be blurred, making LP number recognition partially or completely impossible. If the video camera is not forced to operate at high shutter speed, it will automatically switch to long exposure in case of poor lighting conditions, preventing plates recognition. With the same settings, the video camera can recognize the numbers in bright light only, automatically switching to short exposure.
If the video camera is installed at an angle more than 10 degrees to perpendicular to the license plate, we recommend to halve the shutter speed.

6

Color

Black and white image

It is recommended to use black and white cameras unless it is necessary to store color pictures of the vehicle. This is because clolr cameras while having same characteristics have less sensitivity and pictures appear less sharp.

7

Video stream speed (fps)

See the corresponding module functionality description.

For proper recognition, the plate is to be fully observed and read at least in one frame. For getting the car direction, the plate is to be fully observed and read at least in two frames. The maximum speed of vehicles moving in the control zone is defined for each object and depends on the way of camera installation, what objective is in use, etc. In some frames the plate can be light-struck/darkened/covered depending on the traffic situation, the time of day, etc. To avoid such problems, it is necessary to increase the number of frames in which the plate is observed. It is achieved by the video stream speed-up or decreasing of maximum allowed speed of a car.

The following video camera requirements should be met in order to ensure the recognition of license plate numbers using the Auto-Intellect system.

  • license plate number should be fully placed in the frame;
  • symbols should be sharp, not smeared, undistorted, not overexposed, evenly lighted;
  • symbols should be visually differentiated;
  • technical requirements for the number plates should follow according government standards;
  • without the effect of interlacing (on speed) for analog cameras.
  • No labels