Versions Compared

Key

  • This line was added.
  • This line was removed.
  • Formatting was changed.

The pose The Pose detection is configured as follows:

  1. Go to the Pose detection object settings panel, which is created on the basis of the Person location tracker object.
  2. Specify Configure the perspective on of the video image on which the human location will be detected:

    1. Click the Settings button (1). As a result, the Detection settings window will open.

    2. Click the Stop video button (1) to capture the video image.

    3. Specify the size of the same human at least three calibration segments in three different parts of the frame (2) with the calibration segments.   To create a calibration segment, click and hold the left mouse button on the video image so that you can specify the necessary length size. You can change the size of the already created segments using nodes. The calibration the anchor points. The calibration segments should be located at located at different angles to each other depending on the scene and the distortion of the video image.

      Info
      titleNote
      To delete the created segment, click thebutton (3).


    4. Click Click the OK  button (4).
  3. Set the Trigger an Generate alarm on camera checkbox (2) if it is also necessary to trigger an alarm on the camera by the specified pose detection.
  4. In the Alarm border color field (3), specify the color of the alarm border using the color palette. The default color is red. Double click the color field to open the Color palette. After selecting the border color, click the OK button to save the settings.
    Image Added
  5. In the Number of frames for decision making (1-20) field (3), enter the required amount of frames from 1 to 20 on which the human should be found in the specified pose to trigger the corresponding event. The default value is 2.
  6. From the Type Position drop-down list (4), select the human type position which is necessary to detect:

    1. Sitting person detection — the detection triggers when a sitting human is found in the frame.

    2. Recumbent person detection — the detection triggers when a recumbent human is found in the frame.

    3. Hands up detection — the detection triggers when a human with hands raised is found in the frame. The hand is considered to be raised if the forearm is parallel to the backbone

    . If this type
    1. and the wrists are above the shoulders. If this detection is selected, the following additional settings will become available:

    Image Removed
    1. Image Added

      • Working mode — sets the hands position at which the alarm event will be generated.
    Active shooter
    1. Person detection — the detection triggers when a human

    reaching his/her hand forward parallel to the ground is found
    1. in

    the frame. Person detection — the detection triggers when
    1. any pose

    of a human
    1. is found in the frame.

    2. Close-standing people detection
    — the
    1. — the detection
    triggers if
    1. triggers if the distance between two people is less than specified.
     If
    1. If this
    type
    1. detection is selected, the following additional settings will become available:
    Image Removed
    1. Image Added
      • Calibration column length [0, 3]
     —
      • sets the length of the calibration segments from 0 to 3 meters, which were set when adjusting the perspective of the video image
    , from 0 to 3 meters.
      • . The default value is 1.7;
      • Distance sensitivity [0, 20]
     —
      • sets the minimum distance between people from 0 to 20 meters.
     If
      • If the distance between people in the frame is equal to or less than the specified
    one
      • value, then the detection will be triggered. The default value is 2;
      • Number of people to alert [
    2
      • 0, 20]
     —
      • sets the number of people who should break the distance for the detection to be triggered.
     Possible
      • Possible values
    :
      • are from 2 to 20. The default value is 2.
  7. Click the Apply button (5).

The pose The Pose detection is now configured.