Versions Compared

Old Version 10

changes.mady.by.user Bahdan Tsiulkou

Saved on

compared with

New Version 11

changes.mady.by.user Bahdan Tsiulkou

Saved on

Key

  • This line was added.
  • This line was removed.
  • Formatting was changed.

...

The settings panel of the ONVIF-Server object is shown in the figure.

The Basic settings tab

The table describes the setting parameters of the ONVIF-Server object.

№ParameterMethod for setting the parameter valueParameter descriptionRepresentationDefault valueValue range
1Identification number*AutomaticallyDisplays the identification number of the ONVIF-Server object in the video surveillance system with distributed architectureNumbers, letters, periods, hyphen, dash, and underscoreNADepends on the number of the ONVIF-Server objects in the video surveillance system with distributed architecture
2Name*Enter the value in the fieldSets the name of the ONVIF-Server object in the video surveillance system with distributed architectureLatin, Cyrillic, and service charactersONVIF-Server

A line containing a sequence of any characters (letters, digits, service characters except > and < characters), case-insensitive.

Number of characters—from 1 to 60

3DisableSet the checkboxDisables the ONVIF-Server object in the video surveillance system with distributed architectureBoolean typeClear

Set—the ONVIF-Server object is disabled and not in use.

Clear—the ONVIF-Server object is enabled and in use.

4ComputerSelect the value from the list

Sets the Computer parent object in the system with distributed architecture to which the given ONVIF-Server object belongs

Names of the Computer objects registered in the systemName of the Computer parent objectDepends on the number of the computers in the video surveillance system with distributed architecture
The Basic settings tab
5PortEnter the value in the fieldSets the port number used to connect to the serverInteger numbersNAFrom 1 to 65535
6IP-interfaceSelect the value from the listSets the network interface (network adapter) used to connect to the serverList of available network interfacesNAThe list of values depends on the network adapters available in the system
7RTSP-serverSelect the value from the listSets the RTSP-server object, the settings of which are applied by the ONVIF-Server object while transmitting the video signal Names of the RTSP-server objects registered in the systemNA

Depends on the number of the RTSP-server objects created in Axxon PSIM

8Use Media2 service
Set the checkboxEnables the ONVIF 2.X standard instead of ONVIF 1.XBoolean typeClear

Set—the ONVIF 2.X standard is used. The video is transmitted in the H264, H265, MJPEG, or MPEG4 formats

Clear—the ONVIF 1.X standard is used. The video is transmitted in the MPEG, MJPEG, or H264 formats

9Allow DHCP setting
Set the checkboxEnables the DHCP supportBoolean typeClear

Set—DHCP is used

Clear—DHCP isn't used

10Discovery modeSet the checkboxEnables the WS-Discovery modeBoolean typeSet

Set—the WS-Discovery mode is enabled

Clear—the WS-Discovery mode is disabled

11BrandEnter the value in the fieldSets the name of the brand that is displayed in the third-party clients that support the video transmission via the ONVIF protocolLatin, Cyrillic, and service charactersAxxonSoft 

A line containing a sequence of any characters (letters, digits, and service characters)

12ModelEnter the value in the fieldSets the name of the model that is displayed in the third-party clients that support the video transmission via the ONVIF protocolLatin, Cyrillic, and service charactersPSIMA line containing a sequence of any characters (letters, digits, and service characters)
13DepartmentSelect the value from the listSets the department in which the users are created when they are added via the ONVIF-Server interfaceNames of the Department objects registered in the systemNA

Depends on the number of the departments registered in Axxon PSIM

14Use RTSP over HTTP ProxySet the checkboxRedirects all RTSP-Server and ONVIF-Server requests to the specified port for the operation behind NATBoolean typeClear

Set—the RTSP-Server and ONVIF-Server requests are redirected to the specified port (item 15)

Clear—the RTSP-Server and ONVIF-Server requests are transmitted to the port specified in the Connection settings group (see item 5 above)

15PortEnter the value in the fieldSets the port number for the RTSP-Server and ONVIF-Server requests redirection for the operation behind NATInteger numbersNAFrom 1 to 65535
16NAT IP addressEnter the value in the fieldSets the IP address that the ONVIF Server will use in responses to Clients if the Clients are behind NATIP addressNADepends on the network settings behind NAT

...