Page History

The The ZK Teco door for the controller C3-100 is configured on the settings panel of the corresponding objects AC ZK Door C3-100 object which is , AC ZK Door C3-200 and AC ZK Door C3-400 which are created on the basis of the AC ZK ZK Controller C3-100 object on the Hardware tab of the System settings dialog window, AC ZK Controller C3-200 and AC ZK Controller C3-400 objects.

To configure the ZK Teco door, do the following:

1. Go to the settings panel of the AC ZK Door C3-100 objectobject which corresponds to the required ZK Teco door.
   
2. From the Number: drop drop-down list select the number of the door (1), select the door number.
3. From the Type: drop drop-down list (2), select the type of verification (2)verification type:
   • Fingerprint - it is necessary to provide only a fingerprint to verify the user.
   • Card - it is necessary to provide only an access card to verify the user.
   • Card or fingerprint - it is necessary to provide either a card or a fingerprint to verify the user.
   • Card and fingerprint - it is necessary to first provide a card, and then provide a fingerprint to verify the user.
   • Card and password - it is necessary to first provide a card, and then enter the password to verify the user.
4. In the Emergency: field  field (3), enter the password for door open (3), which is used to open the door without verification.
5. In the Duress: field enter the password for door open  field (4), enter the password which is used to open the door without verification and triggering the alarm event (4).

6. From the Type: drop drop-down list (5), select the type of door sensor (5).

   Info

   title	Note

   :

   • Disable -

   The door sensor type affects the way pass events are generated.

   Disable:

   • the event about the user's pass is generated automatically, as soon as the user has been identified.

   • Normal open

   /Normal close

   •  - the event about the user's pass is generated when the user actually passes closing the door reed switch.

   • Normal close -

   :

   • the event about the user's pass is generated when the user actually passes

   (by closing or

   • opening the door reed switch

   of the door, respectively)

   • .

7. From the Door hold alarm timeout: drop drop-down list (6), select the time interval during which door is opened (6)in seconds after which, if the door is not closed, a door hold alarm will be generated:
   • Disable - the door holding will not be checked.
   • From 1 sec to 255 sec - waiting time for the door to close.
8. Set the Close and lock checkbox (7) to lock the door after its closing (7).
9. From the Door relay: drop drop-down list select (8), select the time interval of opening interval after which the door after the card presenting (8). Select the Close value for permanent closing the door. Select the Open value for permanent opening the doorwill be opened upon presenting a card:
   • Close - the door will be permanently closed.
   • Open - the door will be permanently open.
   • From 1 sec to 255 sec - waiting time for the door to open.
10. From the Punch: drop drop-down list select (9), select the time interval of card presenting (9)for the card presenting.
    • Disable - the time for the access card presenting is not limited.
    • From 1 sec to 255 sec - waiting time for the access card presenting.

11. Set The first card opens door checkbox (10) if the first card is required to open the door using the first card (10). 

    Info
    title Note.
    Access level of first card for the door opening is configured in the panel of user editing in the Access Manager interface module . In the Level in first card mode field specify the corresponding access level. Image Removed (see Specifics of user configuration in ZK Teco integration module).

    
    

12. Set the Enable checkbox

    to allow using of multicard combinations

    (11) to enable the multicard mode.

    Info
    title Note
    The multicard mode is used to open the door only after presenting more than one user access card combined in one or more groups.

    
    

13. From the drop-down list in the Multicard column (12) select the required multicard combination

    (configuring of multicard combinations is given in the section, 12)

    .

    Info
    title Note
    Up to 10 multicards can be specified for one door.

    
    

14. From the Valid: drop drop-down list (13) select the time zone in which the door is active (13). If the Never value is selected, the door will not operate.

15. From the Keep open: drop drop-down list list (14) select the time zone in which the door will be normally permanently opened (14).

    Info
    title Note.
    The door will be opened in not more than within 1 minute after starting the specified time zone.

    
    

16. From the Region In: drop In drop-down list (15) select the Region object region located in on the site of exit through the door (15)door exit side.
17. From the Region Out: drop drop-down list select the Region object located in the site of entry through the door (16)(16) select the region located on the door entry side.
18. Click the Apply button (17).

To send the specified settings to controller click the Send configuration button on the settings panel of the AC ZK Controller C3-100 object.

Configuring of the C3-100 door is completed.

...

...

The ZK Teco door is now configured.