Go to documentation repository
Documentation for Intellect 4.11.0-4.11.3. Documentation for other versions of Intellect is available too.
Previous page Next page
Tables
Designations
The following designations are in the reference guide:
(x32) - HKEY_LOCAL_MACHINE\SOFTWARE\ITV\INTELLECT\ registry section
(x64) - HKEY_LOCAL_MACHINE\SOFTWARE\Wow6432Node\ITV\INTELLECT registry section
For the ATM-Intellect software:
(x32-ATM/Monitoring) – HKEY_LOCAL_MACHINE\SOFTWARE\BitSoft\VHOST\VHostService registry section
(x64-ATM/Monitoring) – HKEY_LOCAL_MACHINE\SOFTWARE\Wow6432Node\BitSoft\VHOST\VHostService registry section
For the ATM Event Capture utility:
(x32-ATM Event Capture) – HKEY_LOCAL_MACHINE\SOFTWARE\ITV\EventATM registry section
(x64-ATM Event Capture) – HKEY_LOCAL_MACHINE\SOFTWARE\Wow6432Node\ITV\EventATM registry section
General information on Windows OS registry and working with it is given in the Working with Windows OS registry section of the Administrator's Guide.
Video | |||||
Registry section | String parameter | Available values | Default | Product version | Parameter in effect |
x32: (X32)\Video | AcsStdLimit | 1-30 | 1 | 4.8.0 and later | Sets the upper limit of succession of frames in the stream in the MJPEG format. If the succession of frames sent to the remote workstation rises to the value specified in the registry key, then scaling is enabled. |
x32: (X32)\Video | AcsMpegLimit | 1-30 | 25 | 4.8.0 and later | Sets the upper limit of succession of frames in the stream in the H.264/MPEG4 format. If the succession of frames sent to the remote workstation rises to the value specified in the registry key, then scaling is enabled. |
x32: (X32)\Video | Activecam | 0, 1 | 1 | 4.7.3 and later | Defines whether to activate the camera by the first click. |
x32: (X32)\Video | ActivateTelemetryHotkeys | 0, 1 | 0 | 4.8.2 and later | Defines whether the Telemetry control via hotkeys is activated. |
x32: (X32)\Video | AdaptiveClientFrameSkip | 0, 1 | 1 | 4.8.2 and later | When the value is 0, then scaling on the Server is disabled. It is better not to disable scaling. |
x32: (X32)\Video | AdaptivePlayer | 0, 1 | 0 | 4.7.6. HOTFIX build 214 and later | The key is created on the Server. It defines whether the AdaptivePlayer is enabled. When the playback speed is changed, the Client sends data about new speed to the Server. Every time there is the change the Server clears the succession of frames sent to the Client and starts creating a new one with scaling specified by the Client. Hence, the Client does not get every frame – this reduces the Server load. |
x32: (X32)\Video | FastPlayStep | 1-6 | 1 | 4.8.0 and later | The key is created on the Client. It allows setting the step of playback speeding-up. Example: for the 3 value the speeding-up step is x6 (i.e. playback speed can be x6, x12, x18, etc.), for 5 - x10. Max playback speed is x60. High playback speed can be achieved when the AdaptivePlayer is enabled. |
x32: (X32)\Video | allclientsbps | >=0 | 0 | 4.7.6 and later | Sets the upper limit of total outgoing video traffic: : 0 – not in use; >0 – max bandwidth of outgoing stream for all Video.run clients. |
x32: (X32)\Video | AllowDelete | 0, 1 | 0 | 4.7.3 and later | The key allows deleting files in the archive list when clicking the Del button. |
x32: (X32)\Video | AlwaysServerConnection | 0, 1 | 1 | 4.7.3 and later | Defines whether to connect the Monitor to the Server. |
x32: (X32)\Video\ArchDays | <camera id> | > = 0 | 0 | 4.7.5 and later | Defines whether to store the archive of the specified camera for xxx days. |
x32: (X32)\Video\ArchHours | <camera id> | > = 0 | 0 | 4.7.5 to 4.10 | Defines whether to store the archive of the specified camera for not more than xxx hours. This key can be used only if one disk is selected for storing the archive. Since version 4.10.0 the Store no more than parameter on the settings panel of the Camera object is in use instead of this key. |
x32: (X32)\Video | ArchStatus | 0, 1 | 1 | 4.7.3 and later | Defines whether to send current archive status to the Server. This key can be used only if one disk is selected for recording the archive. |
x32: (X32)\Video | ArchSync | > 0 | 1 | from 4.9.5, 4.8.10 | Defines whether data synchronization between Server and Backup archive is enabled or not. Synchronization is disabled when the value is 0. When the value is > 0 the key sets maximum imbalance of Backup archive depth between channels in minutes. By default the key is not created and its value is 1. The key must be created/modified on the computer corresponding to the Server on the basis of which the Long-term archive object is created |
0, 1 | 0 | 4.7.7 to 4.8.10, 4.9.5 | Defines whether data synchronization between Server and Backup archive is enabled. When synchronization is enabled, the smaller fragments are sent to the Backup archive until the latest recorded fragment is not copied. After this, newly recorded fragments on this camera are not sent until the same number of fragments is copied from every camera. The key must be created/modified on the computer corresponding to the Server on the basis of which the Long-term archive object is created | ||
x32: (X32)\Video | Cfg | - | name | 4.7.3 and later | Sets the name of configuration file. |
x32: (X32)\Video | CheckLostFolders | 0, 1 | 0 | 4.7.3 and later | Defines whether to remove old log files from the oldest directory when going to a new disk. |
x32: (X32)\Video | Compression | 0,1 | 1 | up to 4.8.0 | Defines whether to check and delete the folders and files that are not in the index. |
x32: (X32)\Video | CompressorVersion | 0 - 255 | 110 | from 4.7.3 to 4.9.0 |
The parameter defines the compressor version when the recompression is enabled. 55 value corresponds to MJPEG. |
x32: (X32)\Video | DebugCam.Camera_ ID | 0, 1 | 0 | 4.7.7 and later | 0 - logging is disabled 1 - logging is enabled |
x32: (X32)\Video | DecompressThread | - | - |
| Key is not active. |
x32: (X32)\Video | DecompressWidth<Monitor_number> |
| - | 4.7.3 and later | Sets the size of frame starting from which the <Monitor_number> starts partial decompression of video signal. For instance, when the value of the DecompressWidth1 parameter is 3000, the Monitor1 will not decompress all frames that are less than 3000 pixels. |
x32: (X32)\Video | Delay |
| 0 | up to 4.7.4 | The key specifies the delay (in ms) of sending video to the camera. |
x32: (X32)\Video | Delta | 0, 1 | 1 | 4.7.3 and later | Allow sending only key frames from Server to Client. |
x32: (X32)\Video | Demo | 0, 1 | 0 | 4.7.3 and later | Defines whether the capture cards are in use or video comes from the file. |
x32: (X32)\Video | DetectionFps | 0.3…30 | 2 | 4.7.8 and later | Sets the fps of a detection tool. |
x32: (X32)\Video | DisconnectInactive | 0, 1 | 0 | 4.8.0 HotFix | Defines whether the Monitor disconnects the gate if the screen is minimized: 1 - disconnect inactive monitors from the Servers (gates, archivers) |
x32: (X32)\Video | DLinkHttpPort |
| 80 | up to 4.8.0 | Port for VitaminControll; DLink from 2000 to 6000 series are compatible with it. The key is not in use. |
x32: (X32)\Video | DrawCursor |
| 0 | up to 4.8.0 | The key is not in use. |
x32: (X32)\Video | Drv | - | - | up to 4.7.6 | The key is not in use. |
x32: (X32)\Video | EnableSnapShotMode | 0, 1 | 0 | 4.7.3 and later | Triggers camera in the snapshot mode, for Axis and D-link 900, operates with the delay. |
x32: (X32)\Video | ExportDir | Path to a folder | moduledir + "\export" | 4.7.3 and later | Specifies the directory for saving frames and recordings from monitor interface (but not via background export, see AviExport utility). |
x32: (X32)\Video | ExportTime | > = 0 | 0 | 4.7.3 and later | Specifies time (in ms) for exporting snapshot from live video into jpg. |
x32: (X32)\Video | Filter.Exclude | Event name | not created | up to 4.8.0 | Excludes the events. Format: Filter.Exclude.event_ID. The parameter value is the name of the event to be excluded. Example: "Filter.Exclude.0"="MD_INFO" "Filter.Exclude.1"="MD_START" |
x32: (X32)\Video | FreeMB | > 0 | 1000 | 4.7.3 to 4.9.5 |
Sets free space in the section while storing the archive; when the limit is reached the earliest recordings will be deleted on loop. |
| 5000 | 4.9.6 and later | ||||
x32: (X32)\Video | FreeMbCritical | >0 | 100 | 4.8.4 to 4.9.5 | Specifies free space in the section while loop recording. |
| 1000 | 4.9.5 and later | Sets critical free space; when the limit is reached archive is stored on another disk (if several disks are in use). | |||
| x32: (X32)\Video x64: (x64)\Video | ArchFreeMB | >0 | - | 4.8.8 and later | Specifies free space in the section while loop recording of reserve archive which is not in use for storing reserve archive and can be in use for recording temporary files. If key is not created, the value created by the FreeMB key is in use. |
x32: (X32)\Video | GateNoRec | 0, 1 | 0 | 4.7.3 and later | Defines whether the gate performs recording to the archive. |
x32: (X32)\Video | Hide | 0, 1 | 1 | 4.7.3 and later | Defines whether the "Hide Monitor" button is visible or hidden: 0 – hidden, 1 - visible. |
x32: (X32)\Video | HideMask | 0, 1 | 0 | 4.7.3 and later | Defines whether to hide the image with the mask filled with black. |
x32: (X32)\Video | Hubslowspeed | 0, 1 | 0 | 4.7.3 and later | For wavehub. Affects fps. Slows down the multiplexer stepping rate. |
x32: (X32)\Video | HWCompression | - | 3 |
| The key is not in use. |
x32: (X32)\Video | Index | - | 2 | 4.7.3 and later | Shows whether file indexing is in use. The value is not to be modified as file indexing is always in use. |
x32: (X32)\Video | InfinityAutoturn | - | - | up to 4.7.6 | Defines on what Infinity cameras the autoturn is to be enabled (camera IDs are specified and separated by commas). |
x32: (X32)\Video | IPCamPort | 0 -65535 | 80 | up to 4.7.6 | Port for IP cameras; action available: connect via the specific port. |
x32: (X32)\Video | IsPeriod | 0, 1 | 0 | 4.7.3 and later | Defines the period of recording to the archive: |
x32: (X32)\Video | Layout | - | - | 4.7.3 to 4.11.0 | The key cannot be modified. |
| x32: (X32)\Video\Layouts x64: (x64)\Video\Layouts | layout<number> | - | - | 4.11.0 and later | The keys store info on layouts of the Video surveillance monitor. The keys cannot be modified. |
x32: (X32)\Video | LH_Timeout | 5-2147483647 | 5 | 4.7.3 and later | Time in seconds on the expiry of which it is considered that there is no connection with Linux Hub. Default value - 5 seconds. Time interval is calculated by formula (LH_Timeout*1000/5) ms, for reconnections to Linux Hub: the more the value the more unlikely the video stream reconnects to LH. |
x32: (X32)\Video | ManualBrightnessControl | 0, 1 | 1 | 4.7.7 | Defines the way of brightness and contrast control for IP cameras: 1 - enable the manual brightness and contrast control; 0 - brightness and contrast are set in the camera interface. |
x32: (X32)\Video | MaxFrames | 500-10000 | 500 | 4.7.3 and later | Sets the number of frames in the file. |
x32: (X32)\Video | Missed | 0 - 2,147,483,647 | Depends on the "mode" parameter of the video capture card | 4.7.3 and later | Sets the video digitization rate. By default the rate is the same as for the video capture card. |
x32: (X32)\Video | Mobile | - | 0 | up to 4.7.6 | The key is not in use. |
x32: (X32)\Video | Monitor<monitor id>_cw | >=0 |
| 4.8.3 | Sets the number of cameras across (the "All cameras" button). |
x32: (X32)\Video | monitor<monitor id>_ch | >=0 |
| 4.8.3 | Sets the number of cameras vertically (the "All cameras" button). |
x32: (X32)\Video | monitor<monitor id>_w43 | >=0 | 4 | 4.8.3 | Sets the frame width (against the frame height). |
x32: (X32)\Video | monitor<monitor id>_h43 | >=0 | 3 | 4.8.3 | Sets the frame height (against the frame width). |
x32: (X32)\Video | NewCompressor | 0, 1 | 1 | 4.7.3 and later | Defines whether to use a new motionWavelet compressor: |
x32: (X32)\Video | NewMD | 0, 1 | 0 | 4.7.6 and later | Defines whether to use a new motion detection tool. |
x32: (X32)\Video | Noallcamsbutton | 0, 1 | 0 | 4.7.3 and later | Defines whether to show the "All cameras" button on the screen. |
x32: (X32)\Video | NoLayoutControl | 0, 1 | 0 | 4.7.5 and later | Disables F1 and F2 hotkeys (monitor ratio). |
x32: (X32)\Video | No_main_panel | 0, 1 | 0 | 4.7.3 and later | Defines whether to display control panel on the monitor. |
x32: (X32)\Video | Nosign | 0, 1 | 0 | 4.7.6 and later | Disables encryption of the digital signature to the frame. |
x32: (X32)\Video | OldDriver | KV1999 KV2000 KV2001 KV2002 KV2003 | Empty string | 4.7.3 and later | Support for old ISS cards. |
x32: (X32)\Video | Oldxeon | 0, 1 | 0 | 4.7.6 and later | Support for old Xeon processors. |
x32: (X32)\Video | Onevideoout | 0, 1 | 0 | 4.7.3 and later | Defines whether video outs are combined on the FS6 video capture card. |
x32: (X32)\Video | OnlyServerConnection | 0, 1 | 0 | up to 4.7.6 | If the video gate is a recording one, then it is possible to enter the archive mode by the short click. |
x32: (X32)\Video | Overlay | - | 1 | up to 4.7.6 | The key is not in use. |
x32: (X32)\Video | PostAlarmTime | >= 0 | 2 | 4.7.3 and later | Sets time (sec) on the expiry of which the alarm by detection tool on Axis IP cameras is not recorded. |
x32: (X32)\Video | PreCompress | 0, 1 | 1 | 4.7.3 and later | Defines whether to compress pre-recorded video. |
x32: (X32)\Video | PrintFontSize | Any | 0 | 4.7.3 and later | Sets the font size for printing. |
x32: (X32)\Video | PriorityClass | 256, 128, 32768, 32, 64 | 16384 | up to 4.8.0 | Defines the stream priority: 256 - realtime |
x32: (X32)\Video | Rbapp | - | - | 4.7.3 and later | Specifies the path to the app run by right-click in the monitor. |
x32: (X32)\Video | IndexRebuilding | 0, 1 | 0 | 4.7.6 and later | Is used when index is being rebuilt. If the system detects IndexRebuilding=1 at start, then index is immediately rebuilt without trying to read idx files. |
x32: (X32)\Video | ReCompressMedia | 0, 1 | 0 | from 4.7.3 to 4.9.0 | Defines whether to enable recompression of video from IP camera (recompress data from IP camera into wavelet). |
x32: (X32)\Video | Remote_delta | - | - | up to 4.7.6 | The key is not in use. |
x32: (X32)\Video | RestoreMode | 0, 1 | 1 | from 4.7.4 HOTFIX | Defines whether to quit the archive upon time-out. |
x32: (X32)\Video | ShowDate | 0, 1 | 0 | from 4.7.3 to 4.8.6 | Defines whether to show the date on the video. |
x32: (X32)\Video | ShowID<Monitor_number> | 0, 1 | 1 | 4.9.0 to 4.10.1 | Defines whether to show the Camera ID on the button to open Camera context menu. Example: ShowID3=0 – the camera number will not be displayed in context men for the third Monitor. |
x32: (X32)\Video | ShowName<Monitor_number> | 0, 1 | 0 | 4.7.3 to 4.10.1 | Defines whether to show the Camera name on the monitor. |
x32: (X32)\Video | ShowTime<Monitor_number> | 0, 1 | 1 | 4.7.3 to 4.10.1 | Defines whether to show the Time on the monitor. |
x32: (X32)\Video | ShowTitle | 0, 1 | 0 | 4.7.3 to 4.10.1 | Defines whether to show the monitor name instead of the time on the control panel. |
x32: (X32)\Video | ShowButtons<Monitor number> | 0, 1 | 1 | 4.10.0 to 4.10.1 | Sets if the buttons of camera number are displayed on the Surveillance monitor <Monitor_number>. If the monitor number is not specified, the buttons are not displayed on all monitors. |
x32: (X32)\Video | ShowBorder<Monitor_number> | 0, 1 | 1 | 4.10.0 to 4.10.1 | Sets if the borders are displayed around the Surveillance monitor <Monitor_number>. If the monitor number is not specified, the border is not displayed on all monitors. |
x32: (X32)\Video | Sigma | - | 35 | up to 4.7.6 | Compressor setting. |
x32: (X32)\Video | SnapShotTime | > 0 | 1 | 4.7.3 and later | Sets time (sec) between snapshots. |
x32: (X32)\Video | Speaker | - | - | up to 4.7.6 | The key is not in use. |
x32: (X32)\Video | Threshold | - | 1500 | up to 4.7.6 | Compressor setting. |
x32: (X32)\Video | TMDCorrellation | 1-100 % | 30 | 4.7.6 and later | Permissible minimum similarity between frames when they are considered to coincide. 100% for completely identical frames. |
x32: (X32)\Video | TMDNonCorrectionStop | > = 0 | 1 | 4.7.6 and later | Number of incoming frames from PTZ camera upon STOP command; the decision to stop pointing (if there is no command to start motion) is made. |
x32: (X32)\Video | TMDSpeed | - | 3 | up to 4.7.6 | The key is not in use. |
x32: (X32)\Video | TMDSpeedCutoff | 0..∞ | 15 | 4.7.6 and later | Sets the limiting value of speed for camera with automatic centering. |
x32: (X32)\Video | TMDTolerance | - | 50 | 4.7.6 and later | Sets pointing accuracy (zone of tranquility). Corresponds to the value of area around stop point of PTZ camera (px). |
x32: (X32)\Video | UseConfigureByWeb | 0, 1 | 0 | 4.7.3 and later | Defines whether to use IP camera settings. When this key is enabled, the driver will try not to change parameters set on the camera. But behavior depends on specific camera+driver version+firmware combination. |
x32: (X32)\Video | UseCompression. | 0, 1 | 1 | 4.7.3 and later | Defines whether video compression is in use (UseCompression.camera ID). |
x32: (X32)\Video | UseLowRefFramesFpsFix | 0, 1 | 1 | 4.7.8 and later | Enables stream decompression with low key frame fps. Threshold fps value = 2. |
x32: (X32)\Video | VideoDumpMode | 0, 1, 2 | 0 | 4.7.8 and later | Sets the mode of video dump: |
x32: (X32)\Video | VideoDumpPath | - | Intellect/ FrameDump | 4.7.8 and later | Path to the folder where frames are stored. |
x32: (x32)\LMCGate | ExportFrequency | - | - | up to 4.7.6 | Sets time (sec) for updating buffer. |
x32: (x32)\LMCGate | EnableExport | 0, 1 | - | up to 4.7.6 | Defines whether frame buffer is enabled. |
x32: (x32)\LMCGate | ExportPath | - | - | up to 4.7.6 | Value is the path to the folder with exported frames. |
x32: (X32)\Video | AdaptiveStream | 0, 1 | - | 4.8.3HotFix |
The key can be used with multistream cameras only. 1 - video stream is transmitted over the network if video from this camera is required. If video is not displayed on the Client, then the there is no stream from the camera and the network is not loaded. Important! When the value of the key is 1, video is not recorded to the archive when the Video surveillance monitor is hidden. But recording is not stopped. In the result video archive fragment the period over which the Video surveillance monitor was hidden will look like a freeze frame. 0 - video stream is transmitted over the network regardless of whether video from this camera is required or not. |
x32: (X32)\Video | ExtractWidth | 0, 1 | - | 4.8.4 | 0 – partial decompression for MotionWavalet is disabled (stream from cameras is enhanced). 1 – partial decompression is enabled. |
x32: (X32)\Video | TelemetryMouseWheel | 0, 1 | - | 4.8.4 | 0 - digital image zooming and Telemetry zoom are performed using the mouse as described in ‘Intellect software package. Operator guide’. 1- digital zooming is performed scrolling the mouse wheel and pressing the Ctrl key. Telemetry zoom is controlled using the mouse wheel: when the wheel is scrolled, ZOOM_IN(ZOOM_OUT) commands are performed; the last mouse click performs ZOOM_STOP command. |
x32: (X32)\Video | ExportFontAdaptive | 0, 1 | - | 4.8.7 | The key sets the relative font size for titles (camera N and time) when the frame is exported: 0 - by default (no key). The size of titles stays the same when the frame is exported (regardless of resolution). |
x32: (X32)\Video | ClientArchMessage | 0, 1 | - | 4.9.0 | The key is in to enable the following events for MONITOR object: ARCH_ENTER - enter the archive; |
x32: (X32)\Video | DrawDetectorNumbers | 0, 1 | - | 4.8.7 | 0 – identifiers of tracking objects are not displayed in the viewing tile (by default). 1 – identifiers of tracking objects are displayed in the viewing tile. |
x32: (X32)\Video | DrawDetectorColors | 0, 1 | - | 4.8.7 | The key sets the color of the frame that marks out the tracking object in the viewing tile: 0 – white color. 1 – the color is calculated as the mean value in the area marked out with a frame. |
x32: (X32)\Video | FaceCamOffset | >0 | 50000 | from 4.8.8 to 4.9.7 | The key specifies the max. possible camera identifier in the system. The bigger values are used for the face detection tool. |
| 2147483648 | from 4.9.8 | ||||
x32: (X32)\Video | FontCamNameHeight | >=10 | 10 | 4.8.8 | The key specifies the font size of the camera name when displaying it on the Video surveillance Monitor. |
x32: (X32)\Video | FontCamTimeHeight | >=10 | 10 | 4.8.8 | The key specifies the font size of the camera time when displaying it on the Video surveillance Monitor. |
x32: (X32)\Video | ShowFileNameInTitles | 0, 1 | 0 | 4.9.0 | The key is used to add the name of the file to the titles using the virtual video device: 0 - the name of the file is not shown in the titles; 1 - the name of the file is shown in the titles (the Captioner object is to be created). |
x32: (X32)\Video | CorrectFrameNumber | 0, 1 | 1 | 4.9.0 | 1 – key redefines frame numbers when archive is played back by Axxon_player.exe if frames are recorded to the archive with incorrect number. 0 – key in not active, frames are played in the order corresponding to their numbers in archive. |
x32: (X32)\Video | DisappearedAlarmDuration | >0 | 15 | 4.9.0 | Key specifies time-out in seconds after which “Disappearance in zone” detection alarm is discarded. |
x32: (X32)\Video | LongInZoneTimeout | >0 | 10 | 4.9.0 | Key specifies time-out in seconds which defines the duration of object appearance in zone, after which “Appearance in zone more than 10 sec” detection tool triggers. |
x32: (X32)\Converter | CheckCompressedSize | 0, 1 | 1 | The key allows decreasing time of exporting video in the avi format using the Converter.exe. utility. If the key value is 0, then resolution check is disabled when exporting video in the avi format. If resolution check is disabled, then frames are not decompressed when being exported, but when resolution is changed, video artifacts can appear. | |
| x32: (X32)\Video x64: (x64)\Video | FastPlayMpegSkip | 0, 1 | 1 | 4.9.0 to 4.9.7 | The key enables frame skip when there is fast playback of the archive in the h264 format. 0 – frame skip is disabled. If the fps value comes up to 50, the frame skip will be enabled regardless of the FastPlayMpegSkip key. 1 – only key frames are played back. 2 (only 4.9.7) – frame skip at fast playback is disabled regardless the fps value. Note. It is also possible to configure frame skipping while playing back the archive – see also info on MonitorSkipArchFramesEnable registration key. |
| x32: (X32)\Video x64: (x64)\Video | MonitorFrameBuffer | >=0 | - | 4.8.2 | The key specifies the number of frames to buffer when displaying live video from IP cameras. The value of 5 is recommended. |
| x32: (X32)\Video x64: (x64)\Video | BoardFX4MaxChannels | 0, 1 | 0 | 4.9.0 | The key enables channel limitation for FX4 card. 1 – the limitation is enabled. It is not possible to set the channel number that is bigger than it is provided by the card. 0 or no key – the limitation is disabled. |
| x32: (X32)\Video x64: (x64)\Video | BoardFS6MaxChannels | 0, 1 | 0 | 4.9.0 | The key enables channel limitation for FX6 card. 1 – the limitation is enabled. It is not possible to set the channel number that is bigger than it is provided by the card. 0 or no key – the limitation is disabled. |
| x32: (X32)\Video x64: (x64)\Video | TelemetryZoomStopTime | >0 | 1000 | 4.9.1 | The key specifies the value of optical zoom duration (delay) in milliseconds. |
| x32: (X32)\Video x64: (x64)\Video | OnvifCompatibilityMode | 0, 1 | 0 | 4.9.1 | The key is for operaton of cameras via the ONVIF protocol in the compatibility mode. It is used when the ONVIF protocol is partially supported by the camera. The key enables the compatibility mode for all cameras in the system. |
| x32: (X32)\Video x64: (x64)\Video | TelemetryPointAndClickDelay | >0 | 500 | 4.9.2 | Sets the interval (in milliseconds) between sending Point&Click commands when controlling PTZ via surveillance monitor by clicking and holding left mouse button and the Ctrl key. See details in Operator's Guide. |
| x32: (X32)\Video x64: (x64)\Video | m_nCurVolume[FS] | >=0 | 0 | 4.7.6 | The parameter is used for loop recording of Server archive in order to store the number of current disk for recording. The figures in ascending order correspond to the letters of the sections (e.g., 0=C, 1=D, 2=E etc.). If the parameter has not been created, then it is created at the moment of selecting the disk for recording the archive with the value of disk number which has the latest recorded archive fragment. When filling the disk, the parameter increases by 1. |
| x32: (X32)\Video x64: (x64)\Video | m_dwTime[FS] | Date in YYYY.MM.DD.HH.MM.SS format | 1970.01.01.03.00.00 | 4.7.6 | The parameter is used for loop recording of Server archive. If the parameter has not been created, then it is created at the moment of selecting the disk for recording with the default value. When going to the new disk, the parameter value changes as follows:
The recording will be performed on the current disk until the file with the date specified in the m_dwTime[FS] key becomes an old one on this disk (if the disk wasn’t primarily empty) or until the remaining free space on the disk becomes equal to that specified by the user (if the disk was primarily empty, see The settings panel for the Video subsystem section). Further the system will erase this file and go to the next disk. |
| x32: (X32)\Video x64: (x64)\Video | m_nCurVolume[ARCH] | >=0 | 0 | 4.7.6 | The parameter is used for loop recording of Backup archive. The parameter is similar to the m_nCurVolume[FS] parameter. |
| x32: (X32)\Video x64: (x64)\Video | m_dwTime[ARCH] | Date in YYYY.MM.DD.HH.MM.SS format | 1970.01.01.03.00.00 | 4.7.6 | The parameter is used for loop recording of Backup archive. The parameter is similar to the m_dwTime[FS] parameter. |
| x32: (X32)\Video x64: (x64)\Video | ResetFastPlay | 0, 1 | - | 4.9.2 |
The key is not created by default, i.e. the value is 0.
The key defines the playback speed if the playbeck is paused and then resumed at fast archive playback:
0 – playback will be resumed with the same speed as before pause. 1 - playback will be resumed with normal speed. |
| x32: (X32)\Video x64: (x64)\Video | TelemetryMouseZoom | 0, 1 | 1 | 4.9.2 | The key allows disabling the control of optical zoom function by mouse buttons. 0 – control of optical zoom by means of long pressing of left or right mouse buttons is not functioned. 1 - control of optical zoom by means of long pressing of left or right mouse buttons is functioned. |
| x32:(X32)\Video\RTSPTimeout x64:(x64)\Video\RTSPTimeout | < camera manufacturer > | 0-100 | 10 | DriverPack 3.2.26.1489 and later | Sets max. time interval at the end of which the following frame is sent through the video gate. Example: in order to limit the frame rate (to 0,01) of the stream transmitted through the video gate using the RTSP protocol, the "RTSP" parameter is to be created with value 100. |
| x32: (X32)\Video x64: (x64)\Video | UnlimitMonitorSize | 0, 1 | 0 | 4.9.3 | When the value=1, the key removes restrictions on the Monitor height and width. When the large size (more than 900%) is set for the Monitor window, then proper operation of Intellect is not guaranteed. |
| x32: (X32)\Debug x64: (x64)\Debug | ShowDisplayingFps | 0, 1 | 0 | 4.9.3 | When the value = 1, the key enables displaying information on fps in the first line of captions on the video image in the Viewing tile. Since version 4.11.0 the name of streaming, codec, resolution (not necessarily displayed on the screen), bitrate, key frame rate (each value in a separate line) can also be displayed. Note. If the debug mode is enabled, the fps of the digitized video signal is displayed on the Monitor (see Frame rate settings), i.e. the key allows comparing these values. The Camera-based Captioner object is to be created in order to use this function. |
| x32: (X32)\Video x64: (x64)\Video | StartPlayFromPFrame | 0,1 | 1 | 4.9.3 | After using frame-by-frame reverse playback, when returning to the normal playback mode: 0 – playback starts from the nearest previous key frame. 1 - playback starts from the nearest previous key frame (difference, R frame). |
| x32: (X32)\Video x64: (x64)\Video | UseServerTime | Comma-separated IDs of cameras in Intellect, or * Note. Use all instead of * value in versions up to 4.9.8 | - | 4.9.3 | Camera sets time of frame while video image transmission after which frames playback by turn depending on the time of frame. Sometimes camera sets incorrect time, so frames playback in invalid order because of bad communication quality or time of camera is not synchronized with server. The key sets list of IP-cameras for which time of frame will be set according to system time of the Intellect server while reading frames from the network. Note. The key can be used for cameras with absolute time (e.g. Tattile cameras). Other cameras synchronize with server time on default. Example. When the value of registry key is “1,10,135”, time of Server will be applied on cameras 1, 10 and 135. If value of key is * then server time will be applied for all cameras. In Intellect 4.10.0 and later this value is considered as the value by default and is in use if the key is not created. |
| x32: (X32)\Video x64: (x64)\Video | MxpegResetCounter | >=0 | 13 | 4.9.5 DP 3.2.30 | The key sets the number of key frames decompressed by MxPEG decompressor before they are returned. The waiting period of specified frames is 3 minutes, on the expiry of this period the decompressor is reinitialized. The key is in use if there is no video in Intellect when MxPEG codec operates with MxPEG decompressor. In this case the value of the key is to be reduced. |
| x32: (x32)\Video x64: (x64)\Video | TelemetryMouseAlternative | 0, 1 | 1 | 4.9.5 | 0 – previously used Mouse PTZ control mode is in use. 1 – a new Mouse PTZ control mode is in use. See Mouse PTZ control. |
| x32: (X32)\Video x64: (x64)\Video | TelemetryLineColor | 4-byte RGB value Most significant byte - 4 = 0. byte 3 - R (0..255) byte 2 - G (0..255) byte 1 - B (0..255) Examples: blue color: LetterboxBackgroundColor = 255 white color: LetterboxBackgroundColor = 16777215 | 16777215 (white color) | 4.10.4 | The key sets the color of the crosshair and the arrow line during PTZ control. See Mouse PTZ control. |
| x32: (x32)\Video x64: (x64)\Video | ContinousMode | Identifiers of cameras, divided by comma, for which continuous PTZ mode is enabled. Example: 2,3,1 | - | 4.9.5 | In the Continous mode camera lens is re-focused slowly – arrow indicating the re-focus direction smoothly follows the pointer. To use the Continous mode, the camera is to support this mode. In discrete mode (if the camera number is not specified in the key) re-focus of the camera objective depends on the area of the mouse click. |
| x32: (x32)\Video x64: (x64)\Video | MonitorSkipArchFramesEnable | 0, 1 | 0 | 4.9.0 to 4.9.4 | The key enables frame skipping while playing back the archive. 0 – all frames are displayed. If there is lack of resources, video delays and loss of synchronization with sound are possible, and the playback speed can be increased no more than 4 times (or no more than 60 fps). 1 – Depends on the version of Intellect:
|
| 1 | from 4.9.5 to 4.9.7 from 4.10.1 | ||||
| x32: (x32)\Video x64: (x64)\Video | TempWritingDir | Path to a folder | - | 4.9.6 - 4.9.7 | The key specifies the path to the existing folder that will be used as a buffer while recording to the archive, e.g., C:\Temp. Temporary files with the name in the writing._<camera_id> format are created in the specified folder while recording. If the key hasn’t been created, then such temporary files are created in the VIDEO folder on a disk with the archive. Important! When 64-bit modules are in use (see Configuring of using 64-bits modules) the key is ignored by the system and temporary files are created in RAM. When the recording is completed these files are renamed and moved to the folder with the archive according to the rules of archiving (see General information on video archiving). This key can be used when, for example, the archive is recorded to the net disk, but disk performance is not enough and it can’t record new files and/or delete previous recordings recorded on loop. If in the key the path to a non-existing folder or a folder created after starting Intellect is specified, then the buffer is not in use. In the TempWritingDir folder there must be MORE free space, than maximum size of temporary files that are stored in it, i.e. the folder must NEVER be filled for 100%. There should be not less than 100 Mb of free space in TempWritingDir folder. To improve performance of data copying from TempWritingDir to NAS create TempWritingDir folder in RAM using special software, for example SoftPerfect RAM disk. |
| x32: (X32)\Video x64: (x64)\Video | MpegWritingQueueSize | >0 | - | 4.9.6-4.9.7 | These keys are used along with TempWritingDir key (see above). They specify the number of frames stored in RAM until data is stored in the buffer for Mpeg and MJpeg codecs respectively. This is necessary for frames not to be lost while copying files from the buffer to the main archive when the disk is full. Values of the keys are to be selected experimentally as they depend on the number and type of cameras as well as on NAS. The values are to be changed at 100 rate. |
| x32: (X32)\Video x64: (x64)\Video | MJpegWritingQueueSize | >0 | 25 | 4.9.6-4.9.7 | |
| x32: (X32)\Video x64: (x64)\Video | ResetOSDLine | 0, 1 | 0 | 4.9.7 | The key is for enabling and disabling titling on the video image using the SC590N4 video capture device. 0 – OSD-captions of device are in use. 1 – OSD-captions of device are not in use. Note. Restart of operating system can be required to apply settings while changing the key value. |
| x32: (x32)\Video x64: (x64)\Video | VMDAEXT | 0, 1 | 0 | 4.9.8 | The key is designed for separating VMDA tracker processes to the individual process. It's recommended to do to increase stability and reliability of the Intellect basic features. Used CPU resources and memory are increasing while separating tracks to the individual process. 0 – process of VMDA trackers is starting in the video.run process. 1 – process of VMDA trackers is starting in the individual detector_ext.run process. Note 1. The detector_ext.run process is run under the video.run process. The video.run process controls the detector_ext.run process and restarts it if necessary. Note 2. It's required to install the Intellect Detector Pack ( version>=2.1.0) for correct key operation. |
| x32: (x32)\Video x64: (x64)\Video | VMDAEXT.RAM | >0 | 300 | 4.9.8 | The key is in use with the VMDAEXT key and sets the memory space in megabytes which can use the detectror_ext.run process. The process will be restarted if allocated memory is exceeded. |
| x32: (x32)\Video x64: (x64)\Video | WritingQueueSize | >0 | x32: 100 x64: default value is a maximal video length in frames (on default 500) | 4.9.8 | The key sets number of frames storing in RAM until start of data record to buffer. The key can be used with any codec. Note. The key replaces MpegWritingQueueSize and MJpegWritingQueueSize keys (see above). Existing values of keys will be read while updating and the maximal value of them will be assigned to the WritingQueueSize key and old keys will be removed. If specified keys are not created, the default value will be assigned to the WritingQueueSize key. |
| x32: (x32)\ x64: (x64)\ | ClearProtocolFromCurrentTime | 0, 1 | 0 | 4.9.8 | The key is for changing the way of deleting archive of events at the end of storage period (see Configuring events logging): 1 – storage period is counted from the current PC time. So if there are events "from the future" (date of which is later than the current date) in the archive of events, they are neither taken into account when deleting old entries nor deleted. 0 – storage period of records is counted from the date of creation the newest record. Note. Deletion is performed at 00:00:00 in case of active license. |
| x32: (x32)\Video x64: (x64)\Video | MemFile | -1, 0, 1 | -1 | 4.9.8 | The key specifies the way of archive record to disk or network storage: 0 – each frame is recording to disk at once. This value is not recommended to use for network storages. 1 – at first video is recording to RAM (default video size is 500 frames, it's specified by the Ring parameter on the Settings panel of the Video subsystem section of the Tweaki.exe utility), temporary files are not created. Video will record on disk after its completion. When the recording ends, it is written to the disk in parts, the size of which is set by the WriteBufferSize parameter (1 MB by default). Memory consumption is highly increasing in this case. -1 – video is recording to disk by pieces in size 1 Mb. This way is optimal when recording to disk or network storage and memory consumption is minimal. |
| x32: (X32)\Video x64: (x64)\Video | WriteBufferSize | >0 | 1 | 4.9.8 | The key specifies the size of video data chunk that is written to the disk at a time, in megabytes. If the frame size is less than the preset value, then it "merges" with the next one. The key is used when the value of the MemFile key is 1 or -1. Note. See WritingQueueSize. |
| x32: (X32)\Video\AVI x64: (x64)\Video\AVI64 | SubtitlesFontSize | >0 | - | 4.9.0 | Font size of captions with camera name and time while export from the Monitor. Note. Captions overlaid using the Captioner object are configured separately on the settings panel of the Captioner object. |
| x32: (x32)\Video x64: (x64)\Video | TelemetryArrowLen | 0 – 100 | 50 | 4.9.8 | The key specifies length of the arrow displayed on the video image at mouse PTZ control from the Monitor window. Arrow length is set in percent and counting from the end. |
| x32: (x32)\Video x64: (x64)\Video | TelemetryStopZone | 2 – 100 | 50 | 4.10.0 | The key sets the size of the zone in the center of the video where PTZ control functions using mouse are disabled. The less the key value the bigger the “dead” zone. The default value corresponds to the size of the cross in the center of Surveillance monitor during PTZ control. |
| x32: (x32)\Video x64: (x64)\Video | ShowTelemetryCross | 0, 1 | 1 | 4.10.0 | The key is designed to enable and disable showing a cross in the center of Surveillance monitor during PTZ control. 1 – the cross is shown in the center of Surveillance monitor during PTZ control. 0 – the cross is not shown in the center of Surveillance monitor during PTZ control. |
| x32: (x32)\Video x64: (x64)\Video | GreenStreamUpdateTimeoutMS | >0 | 20000 | 4.10.0 | The key sets time in milliseconds that equals to stream scan rate in order to optimize connection parameters. This key can be active only if the Video stream setting checkbox is checked (see Configuration of multistream video). |
| x32: (x32)\Video x64: (x64)\Video | TitlesOnlyArchive | 0, 1 | 0 | 4.10.0 | The key is designed to enable saving titles separately from video. 1 – titles are saved in files of *.t01 type separately from video. If there is time stamp in the titles, then these titles are not displayed in live video, but can be seen in the archive (for the corresponding period of time). Titles with no time stamp are displayed on live video 0 – titles are saved with video and are displayed on live video. |
| x32: (x32)\Video x64: (x64)\Video | ExportDirFixed | 0, 1 | 0 | 4.9.9 | The key allows forbidding change of export catalogue when the archive period is exported and when the archive is exported using the AviExport utility. 1 – export catalogue change is forbidden. 0 – export catalogue change is allowed. |
| x32: (x32)\Video x64: (x64)\Video | ShowBookmarkButtons | 0, 1 | 1 | 4.10.1 | The key is used to disable creating and editing of bookmarks meant for protection against video rewriting (see Create a bookmark). 1 – show Create and View bookmarks buttons. 0 – hide Create and View bookmarks buttons. |
| x32: (x32)\Video x64: (x64)\Video | ShowExportButtons | 0, 1 | 1 | 4.10.1 | The key is used to disable export of bookmarks meant for protection against video rewriting (see List of bookmarks). 1 – show bookmark export button. 0 – hide bookmark export button. |
| x32: (x32)\Video x64: (x64)\Video | ResizePrintingFrame | 0, 1 | 0 | 4.10.1 | The key sets the width of frame for printing: 1 – the frame is printed out so that is fits the full width of the page depending on the default layout (portrait or landscape). 0 – the frame is printed out not on the whole page. |
| x32: (x32)\Video x64: (x64)\Video | CycleByLayouts | 0, 1 | 0 | 4.10.1 | The key enables paging by layouts. 0 – standard paging. 1 – paging by layouts. |
| x32: (x32)\Video x64: (x64)\Video | EnableCodecSettings | 0, 1 | 0 | 4.10.1 | The key is in use for enabling compressor and decompressor on the settings panel of the Camera object. 0 – Compressor and Decompressor parameters are not available for changing. 1 – Compressor and Decompressor parameters are available for changing. |
| x32: (x32)\Video x64: (x64)\Video | PerspMaxObjects | >0 | 10 | 4.10.1 | The key sets maximum calibration objects and background points that can be used when configuring perspective for the Tracker object (see Configuring perspective). |
| x32: (x32)\Video x64: (x64)\Video | VirtualGrabberSortMode | 0, 1, 2 | 0 | 4.10.1 | The key sets the order of playing back files when the virtual grabber is in use: 0 – sorting by the latest modification.1 – sorting by name (lexicographic). 2 – sorting by creation time. |
| x32: (x32)\Video x64: (x64)\Video | SplitArchiveIntervals | >0 | 5000 | 4.10.1 | The key is responsible for merging fragments when requesting the range of available archive recordings via HTTP API (see Ranges of available archive recordings). The interval is set in milliseconds. If the time between recordings is less than specified one, then recordings are merged into one. |
| x32: (x32)\Video x64: (x64)\Video | NotifyAbout_arch_days | 0, 1 | 1 | 4.10.2 | The key allows disabling the warning when the Store no less than parameter is set for more than 30% of cameras in the system (see also The Settings panel of the Camera object). |
| x32: (x32)\Video x64: (x64)\Video | archrecrestart | 0, 1 | 0 | 4.8.3 to 4.10.3 | Enables restarting record on archive entering. 1 – patch that has been recorded on archive entering is stopped and a new one starts. As a result the user who enters the archive sees a freeze frame corresponding to that on exiting. 0 – recording is not stopped on archive entering The key is to be created on a Server. |
| x32: (x32)\Video x64: (x64)\Video | MonitorArchPrevTimeSeconds | >=0 | -1 | 4.10.4 | Enables restarting record on archive entering and sets time period in seconds (0 or more) to roll back from current time at archive entering and start playback from. All frames are forced to be recorded to the disk at archive entering, taking into account the pre-alarm recording. -1 – disabled (by default). Note. The key is to be created on a Server. If the key is set to "0", it works in the same way as archrecrestart set to 1 (see above). If "1", "2", etc. is set, the key works in the same way as archrecrestart set to 1 , plus the time for positioning in archive is set. Note. If every 20th frame is a key frame, entering archive can take up to 2-4 sec., as all frames are warranted to be recorded on disk yet it is possible only if the key frame for the next clip is received in order to avoid gaps in the archive. |
| x32: (x32)\Video x64: (x64)\Video | archenterpause | 0, 1 | 0 | 4.8.3 | Enables pausing playback on archive entering. 1 – the Pause button is pressed on archive entering, archive navigation using arrow keys. 0 – the Pause button is not pressed on archive entering. The key is to be created on a Server. |
| x32: (x32)\Video x64: (x64)\Video | FastIndex | 0, 1 | 0
1 | 4.9.9 - 4.10.2
4.10.4 and later | The key enables fast index download. It is in use for 64-bit modules only as memory usage increases while reading and saving. Non-depending on the key value the fastIndex.index file is created in the VIDEO folder - using this file indexes are downloaded much faster. 0 – when Intellect is started all indexes are downloaded, so no time is wasted for data loading. 1 – when Intellect is started the specified file is downloaded and data on detailed index for an hour will be loaded if required. |
| x32: (x32)\Video x64: (x64)\Video | LButtonClickContinuousPlayEnable | 0, 1 | 0 | 4.10.3 | The key changes the playback by alarms control mode in the Video surveillance monitor: 0 - long left-click starts continuous playback of archive fragments, short click starts playback of the current selected archive recording only. 1 - long left-click starts playback of the current selected archive recording only, short click starts continuous playback of archive fragments. |
| x32: (x32)\Video x64: (x64)\Video | MonitorPlaybackControlByMouseWheel | 0, 1 | 0 | 4.10.3 | The key enables control of the playback speed of the archive in the Video surveillance monitor and pausing/resuming playback using the mouse wheel. 0 - playback speed control using the mouse wheel is possible only when the cursor is hovered over the playback control panel. When hovering the cursor over the video, the mouse wheel controls the zoom. Clicking on the mouse wheel is used to control the telemetry (autocentering). 1 - playback speed is adjusted using the mouse wheel while hovering the cursor over the Surveillance window. Clicking the mouse wheel pauses/resumes video playback. Note. See Video playback controls section in Operator's Guide. |
| x32: (x32)\Video x64: (x64)\Video | ConnectOnlyByClient | 0, 1 | 0 | 4.10.3 | The key disables video data transmission from the Server to the Videogate when video data via this Videogate is not requested on the Clients. The key is to be created on the computer under which the Videogate object is created. 0 - video is transmitted from the Server to the Videogate constantly. 1 - video is transmitted from the Server to the Videogate when video data via this Videogate is requested on the Client. If recording to Videogate archive is configured, then to disable video data transmission from the Server to the Videogate, when they are not requested on the Clients, the Active cameras recording checkbox is to be set checked on the settings panel of the Videogate object (see Configuring the record of the Videogate module archive). If this checkbox is set unchecked and recording to the Videogate archive is configured, then video data is transmitted to the Videogate constantly. |
| x32: (x32)\Video x64: (x64)\Video | MaximizeCameraOnDblClk | 0, 1 | 0 | 4.10.3 | The key enables transforming the Surveillance window into the single layout mode by left double-clicking. The key is created on the computer where the video is displayed and the described behavior of the video surveillance monitor is required. |
| x32: (x32)\Video x64: (x64)\Video | MinimizeCameraOnDblClk | 0, 1 | 0 | 4.10.3 | The key is used together with the MaximizeCameraOnDblClk = 1 key and it enables returning to the original layout after enlarging the video surveillance window by left double-clicking. The key is created on the computer where the video is displayed and the described behavior of the video surveillance monitor is required. 0 - returning to the original layout is performed by right-clicking the Surveillance window. 1 - returning to the original layout is performed by left-clicking the Surveillance window. |
| x32: (x32)\Video x64: (x64)\Video | ContourAlways | *, all, IDs of cameras, comma-separated | - | 4.10.3 | The key enables permanent outlining of moving objects on the video from the specified video cameras on all Video surveillance monitors to which it is added. The key is not created or created with an empty value - outlining is enabled by the Operator in the Surveillance window (see Outlining of moving objects). * or all - the permanent outlining of moving objects on all video cameras in on all Video surveillance monitors is enabled. Camera identifiers comma-separated (for example, "1,2,4") - permanent outlining of moving objects is enabled for cameras with the specified identifiers. |
| x32: (x32)\Video x64: (x64)\Video | savemode | 0, 1 | - | 4.10.3 | The key allows not changing the video surveillance mode of the active camera (archive or live video) when changing the layout and adding or removing cameras to the Video surveillance monitor. 0 - when adding a new camera to the Video surveillance monitor and when removing cameras from it, the active camera switches into the live video viewing mode. 1 - when adding a new camera to the Video surveillance monitor and removing the cameras from it, the active camera does not change the video surveillance mode (archive or live video). |
| x32: (x32)\Video x64: (x64)\Video | clean_object_lists | 0, 1 | 0 | 4.10.4 | The key defines if it is necessary to delete cameras from Video Surveillance Monitor list when the Camera object is deleted. 1 – the Camera is deleted from the Monitor list on deletion. 0 – the Camera is not deleted from the Monitor list on deletion. If the Camera object with the same ID is created again, it automatically appears in the Monitor list. |
| x32: (x32)\Video x64: (x64)\Video | ShowDisconnectState | 0, 1 | 0 | 4.10.4 | The key enables displaying a message about a connection failure instead of the last frame received. 0 – When the connection to the camera is lost, the last received frame is displayed in the Surveillance window. 1 – When the connection to the camera is lost, an image showing the disconnected state is displayed in the Surveillance window. |
| x32: (x32)\Video\Deinterlace x64: (x64)\Video\Deinterlace | monitor_id.camera_id, e.g. 4.1 – camera 1 on monitor 4. | 1, 2 | - | 4.10.4 | The key sets deinterlacing mode for the specified camera. By default, the key is not created and mode 1 is in use. In case if it is not productive enough, for example for Paxton intercoms, use mode 2. |
| x32: (x32)\Video x64: (x64)\Video | MonitorMultiDecompress | 0, 1 | 1 | 4.10.4 | The key enables decompression of video on all available cores of the processor, thereby increasing the speed of video playback. 0 - Video decompression is performed on one core of the processor. 1 - Video decompression is performed on all available processor cores. Note. If Clients are present in configuration, set the key both on Intellect Server and Client side. |
| x32: (x32)\Video x64: (x64)\Video | DisableReplaceCam | 0, 1 | 0 | 4.10.4 | The key can be created to prohibit moving the Video Surveillance Windows on the layout in the Video Surveillance Monitor (either when the Control Panel is enabled or disabled). 0 – changing the position of the Video Surveillance Windows on the layout is allowed. 1 – changing the position of the Video Surveillance Windows on the layout is prohibited. |
| х32: (X32)\Video x64: (x64)\Video | EnterEdgeStorageDirect | 0, 1 | 0 | 4.10.4 and later | The key enables the user redirection to the "edge storage" after pressing the Enter archive button. 0 - after pressing the Enter archive button, the user is redirected to the video archive. 1 - after pressing the Enter archive button, the user is redirected to the "edge storage" if there is one, and if it is connected to the camera in the Video Monitor. The key should be specified on those computers where this option is required. |
| 4.10.5 and later | The key ALSO enables the user redirection to the external archive on pressing the Tab hotkey in the Video Monitor. | ||||
| х32: (X32)\Video x64: (x64)\Video | TouchScreeenUpdateTimeout | > = 0 | 0 | 4.10.5 and later | The key sets the Play button hold time in milliseconds to enable the continuous video archive playback on the touch screen. |
| х32: (X32)\Video x64: (x64)\Video | ShowNoDiscIconInMonitor | 0, 1 | 1 | 4.10.5 and later | Using this key you can hide the "no disk" icon from being displayed in the Monitor if no disk is selected for recording. 0 – if no disk is selected for recording, the "no disk" icon is not shown. 1 – if no disk is selected for recording, the "no disk" icon is shown in the Monitor. Note. You should use this key on all computers where the "no disk" icon has to be hidden from being displayed in the Monitor. |
| х32: (X32)\Video x64: (x64)\Video | DisableTelemetryOnDeactivate | 0, 1 | 0 | 4.10.5 | 0 – if enabled, PTZ control remains active after you hide its window or switch to another screen. 1 – if enabled, PTZ control becomes inactive after you hide its window or switch to another screen; you can re-activate it manually. Refer also to Mouse PTZ control. |
| x32: (x32)\Video x64: (x64)\Video | nosynt | 0,1 | 0 | 4.10.5 | This key disables ActiveX's (refer to CamMonitor.ocx ActiveX Control) video stream recalculation to fit the display window and forces video display in its native resolution. Therefore, when you export a frame from an ActiveX window called from the Event Log or the Web Reports subsystem, you'll get full resolution frame from either live video or stored footage. 0 – ActiveX optimizes the video resolution to its window size. 1 – ActiveX displays video in its native resolution. |
| x32: (x32)\Video x64: (x64)\Video | ApplyChinaEastWestFix | 0, 1 | 0 | от 4.10.5 | This key allows flipping the camera icon on the map while you rotate it. 0 – standard behavior. 1 – the Map receives panning value as CAM|XXXX|UPDATE_ABSOLUTE which flips the camera icon while you rotate it. |
| x32: (x32)\Video x64: (x64)\Video | UseNuma | 0, 1 | 0 | 4.10.5 | This key affects the allocation of virtual memory in multi-CPU systems. 0 – uniform allocation of virtual memory. 1 – NUMA allocation for optimal distribution of CPU load between multiple CPUs within a PC. Note. Before changng this key, please consult your AxxonSoft manager. |
| x32: (x32)\Video x64: (x64)\Video | MonitorForwardSkipSpeed | >0 | 12 | 4.10.4 and later | The key operates together with the MonitorSkipArchFramesEnable key (see above). It enables the accelerated playback on reference frames after the specified speed during the 1-camera playback. If the odd number is set as the key value, then the accelerated playback on reference frames will start at an even speed, minus 1 from the entered number. |
| x32:(x32)\Video\FileSystem x64:(x64)\Video\FileSystem | FileReader.MMF | 0, 1 | 0 | 4.10.4 and later | 0 - during the playback, the video archive fragments are read into RAM by one frame. 1 - during the playback, the video archive fragments are read into the RAM all at once. |
| x32: (x32)\Video x64: (x64)\Video | NoSaveTitles | 0, 1 | 0 | 4.10.5 | The key disables storing captions in the captions database: 0 – the captions are saved in the captions DB. 1 – the captions are not saved in the captions DB. |
| x32: (x32)\Video x64: (x64)\Video | <Grabber name.MaxChannels> For example: RTSP.MaxChannels, HikVision(h.264).MaxChannels Note. Both new and old grabber names are supported. The comparison is case sensitive. | >0 | - | 4.10.4 and later, and DP 3.52.2423 and later | The key sets the maximum number of camera channels under the manually created Video Capture Device object for the specified device (grabber). By default, the maximum number of channels is 64. |
Overview
Content Tools