Documentation for Axxon Next 4.5.0 - 4.5.10. Documentation for other versions of Axxon Next is available too.

Previous page Generic Drivers (General device, generic)  Examples of IP device settings for connection via GB/T28181 standard Next page


On the page:

General information on GB/T28181 standard and supported functions

Axxon Next supports connecting devices via the Chinese standard GB/T28181. This standard is based on SIP over UDP (and over TCP since GB/T28181-2016). The GB/T28181 uses the following protocols over SIP:

  • SDP (Session Description Protocol);
  • MANSCDP (Monitoring and Alarming Network System Control Description Protocol);
  • MANSRTSP (Monitoring and Alarming Network System Real Time Streaming Protocol).

This allows receiving the status of sensors, events from detectors, PTZ and relays control, access the built-in archive of the IP device (make sure to set the correct device time zone in the Axxon Next), etc. within the SIP session. Single-channel and multi-channel devices in single-stream mode and working with the UDP and TCP transport protocols is also supported.

At the same level of the OSI model, the RTP/RTCP protocol also works in parallel with the SIP protocol, which makes it possible to use the following functions:

  • video transmission (including archival) in H264, H265, or MJPEG format;
  • audio transmission in G.711a, G.711u, or G.726 format in PS (Program Stream) only. Archive audio is not supported.

For the most up-to-date information on this standard and the features supported in Axxon Next, see the Documentation Drivers Pack.

Configuring an IP-device to operate via GB/T28181 standard

Configuration of IP devices connected via GB/T28181 is performed through the web interface of the devices. Settings are not sent from Axxon Next to the device.

Before connecting a camera via this protocol to Axxon Next, perform the following steps to configure SIP on the device:

  1. Set the Server IP to equal the Server's IP address.
  2. Set the Server port (5060 by default).
  3. Set the Device ID. The ID should be set on all cameras connected via the GB/T28181 protocol and must be unique. The format of the connection code (device ID and server ID) is a 20-digit number:
    1. The first 10 digits specify the address (according to the GB/T-2260-2007 standard).
    2. The next 10 digits indicate device information.
      If the IP device is located behind NAT, then forward and explicitly specify the external address of the Server, the port/port range for receiving video, and the SIP port of Axxon Next Server.
      Example: 34020000001110000001/50557-51557@10.3.3.11/85.172.174.36​
  4. For the device to perform autodiscovery of the Server more quickly, reduce the default value of RefreshRegTime. The name of this setting may vary on some cameras.

Note.

For telemetry to work correctly, set RefreshRegTime to more than 600.

Examples of IP device settings for connection via GB/T28181 standard

Configuring IP-device connection via GB/T28181

Important!

No more than one SIP Server can be used for IP devices connection via the GB/T28181 protocol. This means that several Video Capture Device objects with GBT28181 type can be created in the Axxon Next hardware tree, however, the part of the address after @ must match for all of them. The Server ID, local address, external address, and port must be the same for all devices. If at least one parameter is different (for example, the local IP address is not set for some device when it is set for other devices), then such a device will not start.

Note.

 Axxon Next does not support auto-discovery of devices connected via GB/T28181 and these devices are not added using the Camera discovery tool.

After configuring the device as described earlier, add it to Axxon Next as follows:

  1. Run the IP discovery wizard (see Adding and removing IP devices).
  2. In the form for manually adding an IP device, in the Vendor list, select GBT28181 (1).

  3. In the IP address field specify the value of Device ID parameter set during IP device configuration (2). The following additional parameters can be specified optionally as follows:
    [gbt://]deviceID[/videoPort]@serverID[-serverLocalIP[/serverExternalIP]]
    OR
    [gbt://]deviceID[/videoPortFirst-videoPortLast]@serverID[-serverLocalIP[/serverExternalIP]]
    where:

    • deviceID is the Device ID parameter;

    • serverID is the identifier of the Axxon Next Server generated according to the same rules as the IP device ID (see above);

    • videoPort is the port for receiving video;

    • videoPortFirst – videoPortLast is range of ports for receiving video;

    • serverLocalIP is the local IP address of the Axxon Next Server, which sets the network interface on which the Server should be available;

    • serverExternalIP is the global IP address of the Axxon Next Server; this parameter is in use when the Axxon Next Server is behind the gateway. In this case, this IP address is specified as the SIP Server IP address in the IP device settings.

      Examples.

      34020000001320000008@34020000002000000001
      34020000001320000008@34020000002000000001-10.0.40.246/113.125.160.58 
      34020000001320000008@34020000002000000001-10.0.40.246 
      34020000001320000008@34020000002000000001-/113.125.160.58 
      34020000001320000008/50200@34020000002000000001 
      34020000001320000008/50200-50210@34020000002000000001-10.0.40.246

  4. In the Port field, enter the local port number that the Axxon Next Server shall listen for receiving messages from the IP device (3). Usually this is the default SIP port: 5060.

    Note.

    The IP device SIP port is detected automatically.

  5. The Username and the Password fields are not used (4).
  6. Click the  button.

Connection of the camera via GB/T28181 is now complete.

  • No labels