Configuring Stop In Area

To configure the Stop In Area, do the following:

Create the required detection tool and specify its parameters (see Creating detection tools).
Below the created detection tool, click Create… → Stop In Area.

By default, the detection tool is enabled and triggers when an object stops moving in the area and remains stationary for a specified time.

Note

The object doesn't have to be completely stationary, slight shaking is allowed.

If necessary, you can change the detection tool parameters. The list of parameters is given in the table:

Parameter	Value	Description
Other
Enable	Yes	The detection tool is enabled by default. To disable the detection tool, select the No value
Enable	No
Name	Stop In Area	Enter the detection tool name or leave the default name
Event hold time (sec)	2	Note The parameter is taken into account only if the Trigger on group of objects parameter is enabled. This is the time period during which the detection tool waits for the next objects after the first object in the group is detected. If the specified number of objects (specified in the Number of alarm objects parameter) are detected within this time period, the detection tool triggers. If no additional objects are detected within the specified time period, the detection tool doesn't trigger. Specify the time period in seconds when events will be held when responding to a group of objects. The value must be in the range [0, 86400]
Type	Stop In Area	Name of the detection tool type (non-editable field)
Advanced settings
X-axis offset	15	Specify the X-axis and Y-axis offsets as a percentage of the track area to set the area of the detection tool triggering. The values must be in the range [1, 50]
Y-axis offset	10
Basic settings
Maximum object height	100	Specify the maximum object height as a percentage of the frame size for the detection tool to trigger. The value must be in the range [0.05, 100] Attention! The values of the maximum object height must be equal in the settings of the Object Tracker and Stop In Area.
Maximum object width	100	Specify the maximum object width as a percentage of the frame size for the detection tool to trigger. The value must be in the range [0.05, 100] Attention! The values of the maximum object width must be equal in the settings of the Object Tracker and Stop In Area.
Minimum object height	0.1	Specify the minimum object height as a percentage of the frame size for the detection tool to trigger. The value must be in the range [0.05, 100] Attention! The values of the minimum object height must be equal in the settings of the Object Tracker and Stop In Area.
Minimum object width	0.1	Specify the minimum object width as a percentage of the frame size for the detection tool to trigger. The value must be in the range [0.05, 100] Attention! The values of the minimum object width must be equal in the settings of the Object Tracker and Stop In Area.
Number of alarm objects	2	Note The parameter is taken into account only if the Trigger on group of objects parameter is enabled. This number determines the minimum number of objects that are considered a group and can cause the detection tool triggering. Specify the number of objects that can cause the detection tool triggering. The value must be in the range [1, 100]
Object class	All classes	Select the object class that must trigger the detection tool. The default value is All classes Note When you create the Entrance In Area detection tool below the Object Tracker and select the Person value, the detection tool won't trigger if it detects the movement of several people nearby. When you create the Entrance In Area detection tool below the Category: Face and Category: Vehicle detection tools, the Object class parameter must have the All classes value.
	Vehicle
	Person
Stop in area duration	0	Specify the time in seconds during which the object is stationary for the detection tool to trigger. The value must be in the range [0, 3600] Attention! The value of this parameter must be less than the value of the Time of object in DB parameter in the settings of the Object Tracker (see Setting general parameters of Tracker-based Scene Analytics detection tools). If the detection tool uses the metadata from the Motion detection (see Configuring VMD), the value of the Stop in area duration parameter must be 0. Otherwise, the detection tool won't work.
Trigger on group of objects	Yes	The parameter is disabled by default. If you want the detection tool to trigger only for a group of objects, select the Yes value Note The group of objects that must cause the detection tool to trigger is specified in the Object class parameter. The number of objects that is considered a group is specified in the Number of alarm objects parameter. Waiting time for the next objects after the first object from the group is detected is specified in the Event hold time (sec) parameter. For example, you select the Person object class, the Number of alarm objects is 2, the Event hold time (sec) is 2 seconds, and the Trigger on group of objects parameter is enabled. If the detection tool detects the first person and detects the others within two seconds, these people are considered a group and the detection tool will trigger.
Trigger on group of objects	No

By default, the entire frame is the detection area. In the preview window, you can specify the detection areas using the anchor points (see Configuring the Detection Zone).

Note

For convenience of configuration, you can "freeze" the frame. Click the button. To cancel the action, click this button again.
The detection area is displayed by default. To hide it, click the button. To cancel the action, click this button again.

To save the parameters of the detection tool, click the Apply button. To cancel the changes, click the Cancel button.

Page tree

Documentation for Axxon One 2.0. Documentation for other versions of Axxon One is available too.