The Settings panel of the SIP-device object

The settings panel of the SIP-device object is shown in the pictures below.

Table describes the parameters of the SIP-device system object.

№	Parameter	Method for setting the parameter value	Description	Presented as	Default value	Range of values
1	The Identification number field	Automatically	Shows the identification number of the SIP-device object in the system.	Sequence of numbers	-	Depends on the number of the SIP-device objects in the system.
2	The Name field	Enter the value in the field	Assigns a name to the SIP-device object in the system.	Latin, Cyrillic letters and service characters	SIP-terminal	A line representing a sequence of any symbols (letters, digits, service characters apart from > and < symbols), not case-sensitive. Number of symbols – from 1 to 60.
3	The Disable checkbox	Is set with a checkbox	Shows the status (enabled or disabled) of the SIP-device object in the system.	Boolean type	-	Yes – the SIP-device object is disabled and is not in use. No – the SIP-device object is enabled and is in use.
4	The SIP-terminal dropdown list	Is selected in the list	Assigns the parent SIP-terminal object for the SIP-device object.	Name of the SIP-terminal objects registered in the system.	Name of the parent SIP-terminal object	Depends on the number of the SIP-terminal objects in the system.
5	The Device type drop-down list	Is selected in the list	Sets the icon type to represent the device on the Map.	Names of the available icon types	-	No value touch panel speaker camera microphone default
6	The Device priority drop-down list	Is selected in the list	Sets the priority of a call from this device in the incoming calls window of the SIP panel	Integer	-	0 – 10 The lower the number, the higher the priority and, accordingly, the higher the display in the list. If the field is left blank, then the priority is considered to be minimal. Calls from devices with the same priority will be sorted by the time of the call.
The Device connection settings group
7	The User ID field	Enter the value in the field	Sets the SIP-device identification number, i.e. the number to call it.	Integer		>=0
	The Device IP address field	Enter the value in the field	For SIP-server terminal type only Sets the SIP-device IP address.	IP address		1.0.0.0 - 255.255.255.255
	The Password field	Enter the value in the field	For SIP-server terminal type only Sets the password specified on the SIP-device.	Latin, Cyrillic letters and service characters		A line representing a sequence of any symbols (letters, numbers, service symbols)
	The State field	Automatically	For SIP-server terminal type only Displays the SIP device state	-	-	-

The Video / Audio tab (only for SIP server terminal type)

Table describes the parameters of the Video / Audio tab.

№	Parameter	Method for setting the parameter value	Description	Presented as	Default value	Range of values
1	The Video switch	Set the switch to the required position	Sets the video camera used for calls	Supported options of camera usage	Off	Off — the video is not used during the call. SIP camera — a SIP-device camera connected via the SIP protocol is used. Other — any other camera from the Axxon PSIM hardware tree selected from the Camera drop-down list is used.
2	The Camera drop-down list	Is selected in the list	Sets any video camera used for calls	Name of the Camera objects registered in the system.	-	Depends on the number of the Camera objects in the system.
3	The Audio switch	Set the switch to the required position	Sets the microphone used for calls	Supported options of audio usage	Off	Off — the audio is not used during the call. On — the microphone of the SIP-device is used.
4	The Microphone field	Automatically	Displays the name of the Microphone object corresponding to the SIP device	-	-	-

The Relay tab (only for SIP server terminal type)

Table describes the parameters of the Relay tab.

№	Parameter	Method for setting the parameter value	Description	Presented as	Default value	Range of values
1	The DTMF type drop-down list	Is selected in the list	Sets the type of the tone DTMF command	Supported signal type	sip_info	sip_info – signals are transmitted in the SIP INFO message. sip_notify – signals are transmitted in the SIP NOTIFY message. in_band – the signal is transmitted as normal sound in an audio stream. http_bas – signals are transmitted over the HTTP protocol separately from the voice stream.
2	The Signal duration, ms field	Enter the value in the field	Sets the time period in milliseconds during which the command is to be sent.	Integer		>0
3	The Device connection settings button	-	Opens a pop-up window of connection settings when the http_bas type of tone is selected	-	Inactive by default	-
4	The Name field	Enter the value in the field	Sets the name of the command displayed on the SIP panel	Latin, Cyrillic letters and service characters		A line representing a sequence of any symbols (letters, numbers, service symbols)
5	The Code field	Enter the value in the field	Sets the unique command code	Integer or HTTP request (for http_bas)		A line containing a natural number or HTTP request

The Device connection settings pop-up window

Table describes the parameters of the Device connection settings window.

№	Parameter	Method for setting the parameter value	Description	Presented as	Default value	Range of values
1	The Login field	Enter the value in the field	Sets the user name to connect to the (BasIP) SIP device	Latin, Cyrillic letters and service characters	-	A line representing a sequence of any symbols (letters, numbers, service symbols)
2	The Password field	Enter the value in the field	Sets the password to connect to the (BasIP) SIP device	Latin, Cyrillic letters and service characters	-	A line representing a sequence of any symbols (letters, numbers, service symbols)
3	The IP address field	Enter the value in the field	Sets the (BasIP) SIP device IP address	IP address	-	1.0.0.0 - 255.255.255.255

Page tree

Documentation for Axxon PSIM 1.0.0-1.0.1.